ShawnS Posted February 9, 2012 Share Posted February 9, 2012 (edited) Hi all. To everyone who hasn't seen this on the ozautobuilders forum this is for you. This is my current project and the only thing that I've been working on for almost a year now. I'm about half way through the whole project so I'll fill you in with where it's at and how I got there. THE CAR It's a 1983 Ford XE Falcon S-Pack. The XE Falcon model life lasted from '82 to '84 and it was one of the most popular cars for it's time. The S-Pack was powered by Ford's trusty 4.1L (250) 6 cyl and was basically a stripes and interior trim upgrade over the base model My parents and my grandparents both owned XE S-pack Falcons so they were always part of my childhood and hold many memories for me. It's armed with these memories that I embarked on the most ambitious model project that I could think of and that was to build one (or both) from scratch. This is my parents car. THE BUILD I searched high and low to find a model to base it on but I soon realised that any modification of an existing model would require just as much work as building one from scratch. I thought about it for a while and when I was going through some old car brochures I found a small basic side plan picture of an XD (the Falcon before the XE). I scanned the pic and enlarged it, cleaned it up and made it to 1:25 scale. I drew that onto a sheet of evergreen twice and cut them out. That's when I started adding the detail, first the upper kink in the sides and then I scribed some detail in the sides. Although the real car looks totaly boxy it is has a lot of subtle curves so I had to massage some roundness into the lower areas. The next thing I had to do was to make it thicker to stop it from warping I added thick evergreen into the inside to act as a spine and make it sturdy. I also added more evergreen to the lower inside section later. I scribed the door handles too. The next step was to make something for the window frames and pillars to stick to. The 'L' shaped piece is a spacer that goes inside to bring the windows away from the body. At this stage you can see a strip around the wheel arch that will give me something to stick the putty onto for the wheel arch flares. I made the window frames and pillars from evergreen strips. To be continued. Cheers ShawnS Edited January 15, 2018 by ShawnS Quote Link to comment Share on other sites More sharing options...
ShawnS Posted February 9, 2012 Author Share Posted February 9, 2012 The next step was to putty the wheel arches. I'm not the neatest putty user but it did the job. Then sand them back. It took a little while to get the shape right but I was happy with them in the end. Then it was time to start thinking how I was going to join the two halves. I made steps at either end to glue the hood and trunk to. I made a jig to keep the body sides at the width that I required and glued some bracing inside. I started with the back end. Then I made the hood. Before I glued the hood to the body I made a vent grill from evergreen strips. and glued it in place. The hood had a nose that was added at that stage. Along with a small grill. I was happy enough at that stage to glue the hood onto the body. To be continued. Cheers ShawnS Quote Link to comment Share on other sites More sharing options...
glenn Posted February 9, 2012 Share Posted February 9, 2012 will be watching this closely-great work,isn't the parts box bringing out an xd falcon soon? Quote Link to comment Share on other sites More sharing options...
ShawnS Posted February 9, 2012 Author Share Posted February 9, 2012 The partsbox car will be an XB. Quote Link to comment Share on other sites More sharing options...
DANB Posted February 9, 2012 Share Posted February 9, 2012 I will have to try this ozautobuilders forum out. Your doing a prety sweet job mate! Quote Link to comment Share on other sites More sharing options...
Tony T Posted February 9, 2012 Share Posted February 9, 2012 Fabulous scratchbuilding there!! Quote Link to comment Share on other sites More sharing options...
dodgefever Posted February 9, 2012 Share Posted February 9, 2012 Real scratchbuilding, that's impressive! Quote Link to comment Share on other sites More sharing options...
brett Posted February 9, 2012 Share Posted February 9, 2012 guys, you have not seen anything yet, keep watching, it only gets better Quote Link to comment Share on other sites More sharing options...
Cool Hand Posted February 9, 2012 Share Posted February 9, 2012 (edited) X2 with what Brett said. Have seen this being built on the Oz forum and have to say Shawn is very highly skilled and this build is one of the most impressive Australian scratch builds I have ever seen. Wait til you guys see the amount and the quality of scratch building he has done. Edited February 9, 2012 by Cool Hand Quote Link to comment Share on other sites More sharing options...
Dr. Cranky Posted February 9, 2012 Share Posted February 9, 2012 Oh boy, talk about beautiful building from scratch. Definitely pure eye candy already and the results are looking excellent. Keep it going, please. Quote Link to comment Share on other sites More sharing options...
vwrabbit Posted February 9, 2012 Share Posted February 9, 2012 Great googlymoogly that's fabulous work! Don't keep us waiting! Tim Quote Link to comment Share on other sites More sharing options...
patami Posted February 9, 2012 Share Posted February 9, 2012 THE CAR It's a 1983 Ford XE Falcon S-Pack. This is my parents car. Cheers ShawnS Looks alittle like the Ford granada that we here in europe had about the same time. It thou got an Colone 2.8L V6 as the top end configuration. But the side line and the back light apears to be the same. I have ovned one and have to say it s the best car i have had so far. So yes i vill follow this very closely and have to order a copy if PB starts to sell them. Quote Link to comment Share on other sites More sharing options...
shucky Posted February 9, 2012 Share Posted February 9, 2012 VERY awesome job, cant wait to see more. Keep the updates coming + thanks for sharing. Quote Link to comment Share on other sites More sharing options...
espo Posted February 9, 2012 Share Posted February 9, 2012 This is truely amazing. This man has "SKILLS". Quote Link to comment Share on other sites More sharing options...
Darin Bastedo Posted February 9, 2012 Share Posted February 9, 2012 in-freakin'-credible! Love it. You have some skills! Quote Link to comment Share on other sites More sharing options...
Duntov Posted February 10, 2012 Share Posted February 10, 2012 WOW..... a "REAL" modeler at work....this I have to watch!!!! Regards Bill (Duntov) Quote Link to comment Share on other sites More sharing options...
ShawnS Posted February 10, 2012 Author Share Posted February 10, 2012 Thanks everyone, There is a fair bit left to show you so I hope you will enjoy what I have to show. Although I have taken hundreds of pics so far over the course of the build (and will probably take hundreds more), you guys are getting the edited down version. Looks alittle like the Ford granada that we here in europe had about the same time. It thou got an Colone 2.8L V6 as the top end configuration. But the side line and the back light apears to be the same. I have ovned one and have to say it s the best car i have had so far. So yes i vill follow this very closely and have to order a copy if PB starts to sell them. Yeah I've had a few people tell me the same over the last 12 months and I can tell you that although the Falcon and the Granada are from the same family and have similar styling cues, they don't actually share any parts. Also TPB won't be selling these. It's all mine and I probably won't sell them either but I haven't made up my mind on it yet. Back to the pics. I glued the hood on first then I glued on the windscreen. The thick strips that you can see on the side were there temporarily to keep the body sides in position in the jig while the glue dried. I then turned my attention to the rear end treatment. The first thing to do was to bend a wide thin strip of evergreen and wedge it into the space around the tail light section. This was then trimmed down to replicate the trim around the tail lights. I made the rear bumper. The tail lights were made by scribing the lines into a thick evergreen sheet and then I cut and glued two pieces together into an L shape. This photo was taken in the prototype stage and I later re-made the tail lights to fit flush with the sides of the body. I will cast the tail lights in clear resin later. Then I moved on to the front bumper. I cut out and glued together 3 pieces of evergreen sheet then added the sides and the front. I later added the centre section where the licence plate sits. You can see that the top section isn't cut down like the two pieces under it, I did that to keep it solid to reduce any potential warping. To be continued.. Cheers ShawnS Quote Link to comment Share on other sites More sharing options...
ShawnS Posted February 10, 2012 Author Share Posted February 10, 2012 Then it was on to the lower bumper section. I made the sides. At this stage I was a little bit stuck as how to do the complete airdam so I got some of my modelling clay and made a mock- up of how I wanted the whole nose to look. this also gave me the chance to check the proportions. It was at this stage that I found the whole front end was way too big so I spent some time cutting, sanding and re-making every part of the nose until I was happy with how it looked. I eventually found a way to build the airdam. The bumper itself will be cast as a separate part. I added a grill section to the inside. and made some lights from some mirrors that I found in my spares box and little bits of evergreen. Tomorrow- The roof. To be continued.. Cheers ShawnS Quote Link to comment Share on other sites More sharing options...
LAone Posted February 10, 2012 Share Posted February 10, 2012 wow, im so looking forward to how this turns out. Quote Link to comment Share on other sites More sharing options...
hotrod59f100 Posted February 10, 2012 Share Posted February 10, 2012 Wow, your just amazing . I wouldn't get past the idea of wanting to build one. Lol . Are you going to cast it when your done? Quote Link to comment Share on other sites More sharing options...
promo55 Posted February 10, 2012 Share Posted February 10, 2012 Wow, this is incredible work! I can hardly wait to see how this car comes out. Why could'nt Ford have imported these cars to America? Excellent job on a truly unique model! Quote Link to comment Share on other sites More sharing options...
Dr. Cranky Posted February 10, 2012 Share Posted February 10, 2012 Another builder who should consider, after all this hard work, finding a company to make copies of this one. Fantastic, keep it going. Quote Link to comment Share on other sites More sharing options...
Rob Hall Posted February 10, 2012 Share Posted February 10, 2012 Very cool scratchbuilding effort. Quote Link to comment Share on other sites More sharing options...
Dave Van Posted February 10, 2012 Share Posted February 10, 2012 WOW!!! Great work for sure....are you going to cast it??? Seems like a lot of wok for just one!!! Quote Link to comment Share on other sites More sharing options...
george 53 Posted February 10, 2012 Share Posted February 10, 2012 YOU Sir, are NOT just a modeler, but an ARTISTE! Once had some clown tell me HE was an Auto REPLICATOR, NOT a builder. Well, compared to YOU, he's a NOTHING! This is gotta be one of THE COOLEST things I've EVER seen done! You got talent up the ol wazoo!!! I am LOVEING this, please don't stop with the tute, it's going GREAT. I can only WISH to do stuff this cool! You see, YOU ARE a Auto REPLICATOR, and NOT just a builder!!! GREAT job,Mate. Are ALL you Oz guys THIS talented??? Check out Greg Armours big scale 69 Pro Mod Camaro. Wats in the water there????????? Love this thread!!!!! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.