Casey Posted October 27, 2012 Share Posted October 27, 2012 What did Revell do on the '48 Ford Woodie? Decals for the inserts? I want to say the Dan Fink '32 Speedwagon had no decals at all. Quote Link to comment Share on other sites More sharing options...
Aaronw Posted October 27, 2012 Share Posted October 27, 2012 What'd Revell do on the '48 Ford Woodie? Decals for the inserts? I want to say the Dan Fink '32 Speedwagon had no decals at all. Yes, the '48 has decals. Artists oils work well for wood graining, takes a little practice but its not terribly difficult. The long dry time makes the oils very user friendly, very easy to wipe it down and try again if you don't like the result. Here is a tutorial showing wood graining technique on a 1/32 ww1 airplane. http://www.clubhyper...odgrainel_1.htm The stock engine would be a flathead correct? Shouldn't be that hard to scrounge up one of those. What's the Caddy engine that comes in the kit? Quote Link to comment Share on other sites More sharing options...
camaroman Posted October 27, 2012 Share Posted October 27, 2012 (edited) Sharpie make a set of 3 piece "wood" color markers that can be used for woodgraining with decent results. I will try to post pics of the 55 Ford pickup bed that I did with them ... Edited October 27, 2012 by camaroman Quote Link to comment Share on other sites More sharing options...
Casey Posted October 27, 2012 Share Posted October 27, 2012 No, but it wouldn't be difficult to rework it to stock specs. Namely raise the suspension a couple of scale inches. The present exhaust system could be adapted into a stock version. Just so I understand correctly, it's a stock chassis (framerails, suspension, etc), but there are lowering blocks between the axle tubes and leaf springs in the rear and raised "spindles" up front, correct? Is the Revell body channeled? Looks like it in the image above, and if true, I could see that being an issue on the Woody version. Quote Link to comment Share on other sites More sharing options...
Ramfins59 Posted October 27, 2012 Share Posted October 27, 2012 A suggestion or "tip" re doing woodgrain panels on a Woody..... (Note to Moderators: Sorry if this is in the "wrong place" but since the subject of woodgraining detail on a Woody was brought up) I thought I'd post this "suggestion" here: If you, or any of your friends, smoke cigars (Dr. Cranky), there are some cigars that come in an aluminum tube with a screw on top. Inside the tube, wrapped around the cigar is a small sheet of wood veneer "paper". It is curled around the cigar to keep the cigar "fresh" for a period of time... If you can get some of this wood veneer paper, wet it and put it between the pages of a thick phone book or something similar so when it dries it will lay flat. Then, take the woodgrain decals that come with the Woody model, and cut them out without leaving much of the clear carrier "edge" around the decal... in other words, try to trim the woodgrain decal to fit into the panel it is supposed to go into on the Woody sides as perfectly as possible. Then lay, or tape the decal on top of the dried, flattened woodgrain paper veneer and cut around the decal with a pair of scissors or a VERY SHARP XActo knife so you have a piece of woodgrain veneer paper the exact size as the decal to fit into the panel on the Woody model (at this point the woodgrain paper is very brittle so be careful that it doesn't start falling apart on you.). Then, after painting the wood framing around the insert panels and letting it dry, "paint" a thin layer of diluted white glue in the recessed panel and insert the piece of woodgrain veneer paper and gently press it down so the white glue will hold it in place. Let it dry completely, then you can either coat it with clear enamel or just spray a clearcoat over the whole model, and the woodgrain will "pop" like it has a coat of varnish. Here are some pictures of a "48 Ford Woody that I built about 10 years ago using this method. The wood veneer paper is great to use for dashboards, consoles, door panels, floors, etc.... Quote Link to comment Share on other sites More sharing options...
CEKPETHO BCE Posted October 28, 2012 Share Posted October 28, 2012 All 1:1 1949 Merc wagons were woodies. Thanks for the info. I never knew that. I seen some pictures somewhere on the net, but I guess they were custom. There's a topic on HAMB about it, including pics of a model. http://www.jalopyjournal.com/forum/showthread.php?t=194300 Quote Link to comment Share on other sites More sharing options...
Craig Irwin Posted October 28, 2012 Share Posted October 28, 2012 Thanks for the info. I never knew that. I seen some pictures somewhere on the net, but I guess they were custom. There's a topic on HAMB about it, including pics of a model. http://www.jalopyjou...ad.php?t=194300 Anythings posible with a Sawzall and a MIG welder, I guess I should have stated all factory produced 1:1 1949 Mercury wagons were woodies! Quote Link to comment Share on other sites More sharing options...
charlie8575 Posted October 28, 2012 Share Posted October 28, 2012 Actually, Rich, that wood "paper" is in fact a super-thin piece of wood, usually cedar. This is to help keep the cigar from drying out, something like a micro-mini humidor. Charlie Larkin Quote Link to comment Share on other sites More sharing options...
jbwelda Posted October 28, 2012 Share Posted October 28, 2012 hey rich thanks for that tip, not only is it ideal for this new merc woodie, i have another thing going right now where the woodgrain trick is going to work out great. do you have any specifics about which cigars to buy to find this stuff inside? Quote Link to comment Share on other sites More sharing options...
charlie8575 Posted October 28, 2012 Share Posted October 28, 2012 do you have any specifics about which cigars to buy to find this stuff inside? I don't smoke but my dad will have a cigar every so often. Most tube cigars, from what I've seen, will have those thin slivers of wood. Generally, the more expensive it is (usually around $5-7 each,) the more likely you are to find it. Charlie Larkin Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted October 28, 2012 Share Posted October 28, 2012 (edited) Just so I understand correctly, it's a stock chassis (framerails, suspension, etc), but there are lowering blocks between the axle tubes and leaf springs in the rear and raised "spindles" up front, correct? Is the Revell body channeled? Looks like it in the image above, and if true, I could see that being an issue on the Woody version. First question- yes, raised spindles and lowering blocks- but a little cutting and fiddling could revert those to stock height. Second question... again, yes- I forgot that the Revell Merc is channeled. That would be a serious problem if you wanted to build it totally stock! But here's the thing- If I recall correctly, Mercury's Woody Wagon was based on the shorter Ford body- it was just the Ford with a Merc nose bolted on, different doors, and Mercury interior bits. So if that is true, they'd need to do up a new floor as well, because the length would be different. In any case you could probably adapt an AMT '49 Ford or Merc chassis to this body if you wanted to go totally stock. I'll experiment a bit once I get one on the workbench... Edited October 28, 2012 by Michigan Madman Quote Link to comment Share on other sites More sharing options...
Ramfins59 Posted October 29, 2012 Share Posted October 29, 2012 Charlie, I realize that what I called wood "paper" IS actually wood... like a small sheet of a wood veneer...... It's just that it's so thin that I called it wood paper. JB, my cousin smokes cigars and gave me a whole cigar box full of these wood sheets about 4 years ago... he saves them for me. I don't actually know which cigars he smokes, but I know some of them are a little pricey. Quote Link to comment Share on other sites More sharing options...
jbwelda Posted October 29, 2012 Share Posted October 29, 2012 ok thanks i will go check out the local cigar shop. theres a guy here who actually hand rolls cigars...i bet he has got sheets of the stuff. Quote Link to comment Share on other sites More sharing options...
rollinoldskoo Posted January 2, 2013 Share Posted January 2, 2013 I wonder how that visor fits the AMT 51 Chevy cars and the revell/monogram 53/54 cars..... Quote Link to comment Share on other sites More sharing options...
Casey Posted February 11, 2013 Share Posted February 11, 2013 Yes, the '48 has decals. Looking at the test shots on page one, it appears the insert areas are smooth, leading me to believe Revell will include decals for the inserts. I guess those who want to build the '49 Merc Woody stock should pick up an AMT '49 Mercury kit right about now, too. Quote Link to comment Share on other sites More sharing options...
tim boyd Posted February 23, 2013 Share Posted February 23, 2013 Here are the decals from the '48 Ford woody from Revell. They were excellent. Virtually no carrier border beyond the edge of the wood sections, and they fit the openings perfectly. If the '49 Woody has these same type of decals, we'll be in great shape. TIM Quote Link to comment Share on other sites More sharing options...
Junkman Posted February 24, 2013 Share Posted February 24, 2013 (edited) Tbh, the only questions I have are which engine Peter Cochran had in his splinter box, when someone is going to offer resin repops of the Aurora Mod Squad figures and how much he wants for those including postage to England, please. Edited February 24, 2013 by Junkman Quote Link to comment Share on other sites More sharing options...
Craig Irwin Posted March 2, 2013 Share Posted March 2, 2013 Tbh, the only questions I have are which engine Peter Cochran had in his splinter box, when someone is going to offer resin repops of the Aurora Mod Squad figures and how much he wants for those including postage to England, please. They are on ebay all of the time, but make no mention of their mod squad past in the listing. Just resin figures in 1/25. Quote Link to comment Share on other sites More sharing options...
jbwelda Posted March 3, 2013 Share Posted March 3, 2013 i think norm at replicas and miniatures of maryland has "mod" squad figures too. Quote Link to comment Share on other sites More sharing options...
Draggon Posted March 3, 2013 Share Posted March 3, 2013 Uschi Van Der Rosten has woodgrain decals. Gonna buy this one plus his decals and see how it turns out. http://www.uschivdr.com/shop/ Quote Link to comment Share on other sites More sharing options...
carsntrucks4you Posted March 3, 2013 Share Posted March 3, 2013 Uschi Van Der Rosten has woodgrain decals. Gonna buy this one plus his decals and see how it turns out. http://www.uschivdr.com/shop/ Those decals are excellent. I used it on my Modelhaus Merc Woody http://www.modelcarsmag.com/forums/index.php?showtopic=55196&hl=%2B50+%2Bmerc+%2Bwoody#entry646240 or http://www.modelcarsmag.com/forums/index.php?showtopic=54195&hl=%2B50+%2Bmerc+%2Bwoody Quote Link to comment Share on other sites More sharing options...
sjordan2 Posted March 4, 2013 Share Posted March 4, 2013 (edited) One DIY suggestion -- If you download wood pattern samples from wood supplier websites, you can use them as is, or put them into a graphics program and adjust the color, sharpness, size, etc. any way you want and print out on paper or decal paper. Here's how I find what I'm looking for: http://www.google.com/search?tbm=isch&hl=en&source=hp&q=wood+grain+samples&gbv=2&oq=wood+grain+samples&gs_l=img.12..0.1703.5916.0.8714.18.10.0.8.8.0.155.600.9j1.10.0...0.0...1ac.1.3pd-T4OUaRE Just a few examples. Edited March 4, 2013 by sjordan2 Quote Link to comment Share on other sites More sharing options...
charlie8575 Posted April 14, 2013 Share Posted April 14, 2013 Aside from the exhaust and Caddy V8, this thing looks stock. Even the ride height looks about right to me, as the Mercs I've seen do sit low-ish. Not Hudson or Nash low, but they're not sky-high, either. Worst case, I'll just build a load for the back and fold the seat down. It is a station wagon after all, and I use mine! The glass-packs are something I have no objection to, and I can scare up a Flathead somewhere, although I hope they'll simply include one to make life simpler. Charlie Larkin Quote Link to comment Share on other sites More sharing options...
1930fordpickup Posted April 15, 2013 Share Posted April 15, 2013 If they would just make the engine parts on a separate tree's . The 50 ford truck engine would be fine. Just paint it Mercury green. Quote Link to comment Share on other sites More sharing options...
Olskoolrodder Posted April 15, 2013 Share Posted April 15, 2013 That's not necessarily a bad thing,that's one of my favorite kits! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.