Biggu

And this is the basic inspiration for this build altho not the same colors but some of the same bits here and there. The light blue and red trucks were parked at a rest area near Revelstoke BC back in June and the fellow in the red truck was from Quebec and couldn’t speak very good English , but was over joyed when I asked if I could take a few pics of his Pete. He was very proud of it. He was heading to Vancouver Island. No one around the light blue one bit it was REALLY nice.

I used the small interior upgrade set for the dash parts, I like the results. Even had to add the Peterbilt decal on the glove box door

So somewhere along the line I mentioned I was going to add a little pe to this build. I use the CTM stuff and I find it really nice and I’m not a hugely experienced pe guy but it sure adds to the build. So this is big upgrade set I will try to use mostly

Geez, Brian !

Love the Torque Thrusts !….

Probably not a lot this time Brian, it will be clean but not as clean as my Corvette. Ken said I need to slop up the engine with big oil leaks …. LOL

Steering box is in and power steering hoses attached. I will let this set up and then probably the front pulleys and a/c and alternator. Then rad. Thats the tentative plan anyway.

My next thing is the steering box…. I added CTM fittings to the box so that I can hopefully connect power steering lines. And made some caps instead of ‘heat swage’ the pins for the working steering. I have never had lick with the hear swage thing

Ok. We’re in … holy moly that was a tight fit !!! I teat fitted it 3 or four times buy was VERY careful not to break any protruding fittings. To follow the instructions they suggest to remove the small tab on the front engine crossmember so that the engine sits down flat rather than with a front lift. I did that and the engine sits nicely flat on the front cross member and the corresponding rear engine mounts. Looks good , BUT a lot of the finer details are hidden by the frame rails, sadly. All fuel and oil filters and ECM box are tucked away and can only be seen from under the truck. The engine looks every bit the part of the real deal. Also in hind sight or if I were to do this again, I would most definitely sand, or trim, or shave down the top part of the inner frame rail ( as it wouldn’t be noticed anyway) to facilitate an easier and less stressful engine install . As it is I installed the oil filters as close to the engine block as I could as there is a little wiggle room but the filters are still hard against the frame rail. Never the less I shoe horned it into place and it looks good . I dos this install without all the front bits on . I think I can install all the pulleys, fan, a/c, and alternator as the engine sits or I HOPE I can otherwise I may be diddled.

Brian , I wish I could have taken you for a ride. The best nights were a heavy snow storm with LOTS of snow and pushing that one way for hours on end and watching the discharge chute and the thousands of tons of snow blasting onto the shoulder. It was a rush and I loved it. The more snow the better. Also knowing in the back of your mind you were providing some safety to the travelling public. I took a lot of people for rides , you know the ones, those that said all we did was sleep in the trucks? I changed many minds over the years. Most said they didn’t know how we did it and said they couldn’t do it. I think you would have had fun and really enjoyed it. I would love to do it one more time. Lol Jeff

And here is a pic of the engine and transmission finally mated getting ready for frame install. Note that I didn’t put the filter decals exactly the same as they never are in real life , at least never were when I did an oil change. I think it adds just a little dan of realism. Also airline for the range selector

The engine kit comes with a set of VERY small decals but incredibly detailed. So this is about as far as I could go with it out of the truck. Again sorry for the lousy pics, I’m fairly new at this game but you get the idea. The Bendix decal on the compressor is VERY small and you can still READ it ! Now thats detail !

So I have progression on the engine. It is a little jewel. It takes a little delicate painting of fittings etc but if my big fat puds can do it anyone can. With careful detail painting the brass fittings come out nicely. I have added some details but nothing like Randy and his build. His engine detailing is hugely inspiring. ( Floater truck thread ) so here are a few pics of what I was able to put together. I had to add a scratch made dip stick tube which is actually an aluminum tube that had to be bent to ‘spec’ to fit in the fitting in the block

Thanks Jeff. The engine detail is fantastic. I’m trying not to make a pig’s ear out of it. I was a bit pricey but as you mention head and shoulders over the kit one , but with that said I think my next one, I am going to see if I can kick that kit engine up a notch or two. Might be a fun challenge. Maybe … lol. I’m glad to hear you order from Paul too. The more of us that do the better it will be for all of us I think. I see he now has the KGS Loader and excavator. And getting more conversions, looks like I will have to save my paper route money, allowance , lemonade stand money too. Lol. Thanks for checking in I appreciate your comments. cheers Jeff

Thanks Gary. Boy you are sure right about the aftermarket and I am a victim of that. For all the years of building out of the box which is really someone else’s ‘vision’ so to speak, we can now build our own vision. And in some cases much more realistic and each kit can now be different. I have been on this site for a while and have watched a lot of builds and none really box stock and even the slightest modification inspires me to try new things and make my builds a personal thing. There is no wrong way to build and building it ‘your’ way is spot on. That’s why I spend hours here looking at the current and past builds and I gather all sorts of ideas and see new techniques. Love this place. Thanks for you kind words. Jeff

I can’t say anything. My jaw has fallen from my face and is planted on the floor!!!! I am in complete awe in your scratch building and superb engineering. Having had my buttocks in the seat of one of these plow trucks for more years than I want to remember, I can tell you from hundreds of hours and thousands of miles driven this is with out question the MOST stunning and accurate replica of one of our trucks. Your attention to detail and obvious love for these trucks and company is unprecedented, Brian. This is the best truck model I have ever seen. And I KNOW how they should be and look and this is IT! This should find its home at head office in PG as a tribute to the good job we old guys did and the new crews do today. YRB was the BEST company I worked for in my 38 years of highways maintenance. A pure delight to watch this come together Jeff

So in deciding what color I have that may be close to the Detroit color, I discovered that the early 60 Series were the old Detroit green and the newer units were the Detroit ‘blue’. I had a new bottle of Vallejo M-485 Blue Grey an acceptable color choice and with that gave the block a shot. This is my very first foray into acrylic paint as I am a die hard Model Master Enamel guy but someone decided that was to end so now I have to learn new tricks. I have to say so far the paint is good and went thru my airbrush smoothly …

On the block there are 6 1/2 million contact points that need to be nipped off and it takes some time and patience but the little gem inside is more than worth the time and effort to clean it up. There is a fair bit of waste but that is the cost of doing business as they say . The pic is of all the waste bits for the whole engine and there is a bit

So a while ago a fellow on another site mentioned that GP Modeling was in the process of designing a 1/24 scale 3d 60 Series Detroit engine. I aww what was being offered and ordered one, from Spot Model who were excellent to deal with and I had to wait for about a month for it to be in production and shipped to me here in British Columbia. The detail is incredible. And screams for extra detail. ( see Randy’s build in the Floater Truck thread, his is off the clock) so I thought I would give it a go …. Here are some pics as it comes

Thanks , Steve...................I totally agree with the tape , the duct tape should work as well, I have found that if I take a wooden dowel or something like that and really burnish the edges of the tape it seems to help somewhat and doesn't leave a sharp line and I use a circle template to cut the tape, nothing fancy......the brake chambers are from Kootenay 3D Model Parts.... Brandon does really nice work.... his site is down for a little bit by the looks of it, but well worth checking out....

Thanks Brian. Yeah the air detailing does add to the build but at times can be a bit tedious …. There is some “artistic license “ on this one. But I did a Kenworth W 900 to spec. That was a bit of a challenge but turned out quite well

So under a splash of paint and a few decals added to the frame and the Wabco Air drier installed and a few detail bolts the frame is slowly coming together

So now it seems to be air plumbing time. I buy my air valves and my aftermarket from STSupply as Paul is in Canada and it saves me the massive bank exchange fees to US Dollar. So all a/m including rims and tires comes from Paul . That is my main source for A/M. So valves installed and the plumbing started

Thanks for the kind words, Rick..... yeah I do have lots of trees in the yard, and I probably could make some timbers , not sure how good I am at 'whittling'.... BUT who knows, maybe another hobby in the making?? LOL, Good idea, and I will look around and see if I can find some suitable candidates.... thanks for the comments and dropping by Jeff

Sorry for the BLAH_BLAH_BLAH_BLAH pictures, just of my crappy phone....