Force

A polishing kit can save lots of flaws in paint jobs...believe me, I have saved lots over the years since I got mine...but it can't knock down a sharp paint edge and get it level without sanding off the overlaying paint at the edge completely, that's why you need to use clear coats so you will have more paint to work with, after that sand it down to a flat surface. If you sand with a sanding block before the clear coats and get the paint level and get out "orange peel" dust specks and other imperfections the result will be even better and you can use the polishing kit for that, the grit on the abrasive cloths in the kit goes from 1800 grit in 8 stages up to 12000 grit...at least they do in my LMG Enterprises kit...1800 is quite coarse and the 12000 feels almost like the paper newspapers are printed on to the touch. If the paint is decent I usually start somewhere in the middle and go up the grit stages and finish with 12000...and you use them wet.

Looks good. From back in the day when Pro Stock cars looked like a meaner version of the street going counterparts, not like the cars they use in Pro Stock today.

Looks nice. You learn something every day and this forum helps a lot.

I've seen that before and saved all the pictures for references. It's unfortunate Revell didn't do the kit like the original truck was, because it's quite a difference between a Peterbilt 359 and a 379, a Cat 3406 and a Cummins NTC475, so they took quite a shortcut when they did the kit as they based it on the 359 they allready had, the wrecker body looks to be right tho'. On that site there are more photos of other trucks Revell did. Bill Signs Trucking Clydes II Peterbilt 359 http://www.truckin24.de/03c1989d840f69e01/03c1989e1510fe103.html Kenworth W900 Wrecker http://www.truckin24.de/03c1989d840f69e01/kenworthw900wreckeroriginalfotos.html And the Beall Tanker http://www.truckin24.de/03c1989d840f69e01/03c1989d831212610.html They also have photos of trucks they haven't done kits of like Bill Signs Papa Clyde Peterbilt 379 http://www.truckin24.de/03c1989d840f69e01/03c1989f560b54a03.html and a couple more wreckers. A Peterbilt 359 with Holmes 750 http://www.truckin24.de/03c1989d840f69e01/03c1989e520f58710.html A Peterbilt 379 with an All-Pro 70 ton rotator http://www.truckin24.de/03c1989d840f69e01/03c1989e580c35722.html And a Ford LTL 9000 with Vulcan 940 http://www.truckin24.de/03c1989d840f69e01/03c1989e530c5a213.html

Are you sure about that?? I have two "Can-Do" kits issued 1993 and one "Will-Do" kit from 2013 and I just checked, after what I can see the light bars look exactly the same. On he box art they are different tho', the "Can-Do" shows amber light bars and the "Will-Do" shows clear light bars, but they are in clear plastic in all kits. I might get one more if they re-issue it again.

Very nice.

Yes they are too large, a friend of mine have a real "Bathtub" intake manifold and I think they are 1/2 inch bolt heads/nuts. The oil pan looks good tho'

Unfortunately the carbs in most kits are bad and don't look like the carb they are supposed to be, they work if they are covered by an air cleaner but most of them look terrible open with a few exceptions, the last kits AMT developed before the Racing Champions take over had decent carbs like the 1960 Starliner, the 1962 T-bird, the 1971 Plymouth Duster and a couple more. I don't like Holley 4500 Dominators Revell had in their Pro Stock kits that many use on their builds, they are very poor versions of what they are supposed to be and they missed the mark by far, and if you have been around the real ones as I have they definately don't make the cut, the Dominators in their Pro Sportsman kits are a bit better. But the best Holley 4150 and 4160, Rochester and Carter carbs available are the ones Joseph at Fireball offers, and the best Holley 4500 Dominator carb I have found so far are the one Futurattraction does. Expensive...maybe, but if you want the right look...you might have to bite the bullet.

You do as they do on real cars. You can't get the edge completely flat just by sanding directly on the paint, the edge is only paint buildup and if you do you will sand the overlaying paint away before it gets flat. So lay several coats of clear on top of the paint, sand it down with fine wet paper and then polish.

Superb build.

I thought the Torsion Bar went out when the AG100 came, well you learn something every day, I have also read somewhere that a well maintained Torsion Bar rode at least as good as the early AG100. I know Tyrone Malone had the old KW 4-bag on the Boss Truck Of America wich was a 1971 model and on the 1970 Mama Truck transporter as well. The 1976 Papa Truck Transporter had the Torsion Bar and the 1978 Hideout Truck Transporter had the AG100 wich appearantly was new for that year, the 1974 Super Boss and 1978 Bandag Bandit Racing Trucks both had Torsion Bar single drive. Peterbilt's first air ride, the Western Unit Stabilaire, was as I hear quite rough too like the old KW 4-bag, but the later Air Leaf was much better, the Stabilaire was taken over by Freightliner and was called Airliner.

I was going through the MTDG Facebook group just now and noticed a thing regarding the Malone trucks in a thread where Ben Wicker shows the correct style 5-hole Truck Mate wheels he has done the master for and sold by Jamie at Mo'luminum, I'm not a member on Facebook so I give out the information I have here. Someone there said the Hideout Truck had Alcoa 10-hole wheels at one time when Malone had it and they were covered up with Truck Mate stainless steel wheel covers...that's not really the case, Malone was sponsored by Truck Mate (wich is still around) and the Hideout Truck had the stainless steel wheel covers at one time, but under these wheel covers it still has the Truck Mate chromed 5-hole wheels with the same tube tires as before, even the Bandag Bandit had the same wheel covers on the rear wheels at that time...the wheels on most of the Malone trucks was later changed to chromed 2-hole wheels and 24.5" size tubeless tires. I don't think Truck Mate had any 10-hole aluminum wheels at that time and the only pictures I have seen where the Hideout Truck has had 10-hole Alcoas are from after Malone himself had passed and the truck was sold and when the truck was found again not that many years ago. Bridgestone who now owns the Bandag Brand was approached and offered to buy the truck so they could pair it up with the Bandag Bandit they allready have again (sits at the Iowa 80 Truck Stop Museum), a representative from Bridgestone came to California where the truck was and looked at it, they considered to do it but they changed their mind and finally declined...Gary Ries from Hastings MN has since bought the Hideout Truck and is going to restore it like he did with the Papa Truck Transporter he had bought earlier, he also owns the Super Boss, the Whale Truck and trailer, the Hurricane, the Defiance wheel stander Freightliner and the Smokey Bear Corvette from the Malone stable...Gary also tried to buy the Boss Truck Of America some time ago, the truck sits in Texas somewhere but that deal didn't go through, it's in pieces and the owner wants too much for it. Here are some pictures to show what wheels the Hideout Truck has had over the years. First the early Bandag version from approximately 1979-80 with the chromed Truck Mate wheels and tube tires, the first Thermo King version from 1978 did also have these wheels and I have posted a picture of that version earlier in this thread. A version with the Stainless Wheel Covers some years later, around 1981 or so, note that the Bandag Bandit has the same wheel covers on the rear wheels and that truck hasn't had anything else than tube style tires under it's life and it still has. An even later version some years later 1988-89 where Malone had changed to 2-hole chromed wheels with tubeless tires and a different paint job. This picture shows an even later version with the 2-hole wheels and the paint job is changed slightly again, more texts and the outlines of the white yellow and blue stripes on the cab are white instead of gold. Finally the version when the truck was found again in 2009 before Gary Reis bought it, the paint job is still nearly the same as in the picture above but now it has 10-hole Alcoa wheels.

Wasn't the torsion bar suspension obsolete in 1979, I mean Kenworth came with the 8-bag Airglide 100 the year before in 1978. But I have read the Peterbilt Air Leaf offered a smoother ride that the Kenworth AG100 and I have seen lots of pictures of Kenworth's with Peterbilt suspensions.

The Revell AG truck kits are the most expensive truck kits on ebay and the "Can-Do, "Will-Do" and the Bill Signs "Clydes II" kits tops the list and has done for a long time. There are two 1992 issues of the "Can-Do" there right now with asking prices of $575.00 and $720.00, and two 1993 issues of the same kit with asking prices of $460.00 and $475.00. There are also two of the "Will-Do" reissue from 2013 on ebay now wich is the same kit as the "Can-Do" except for the decals, and they have asking prices of $430.00 and $450.00. There are two 1994 issues of the Bill Signs kit there right now too and asking price for them is $350.00 and $500.00, I also saw one 2010 issue of the same kit and asking price for that is $325.00. So they are not cheap...but these are asking prices and if they will sell for that is questionable. What a realistic price is for the first issue of the "Can-Do" I don't really know, it depends on what the buyers are prepaired to pay for the kit and how desirable it is...and they are for sure desirable. I have two of the "Can Do" kits and one "Will Do" kit and I can say I didn't pay nearly as much when I bought them...for the prices they ask now on ebay I'll pass.

Very nice. Where do you get your slicks, they look just right with the wrinkles?

Yes it's not an uncommon thing, kits has come and gone all the time since they started doing them. The tooling is still there but when they don't have anymore in stock of the last batch of a certain kit it's discontinued until they some years later decide to do another batch of said kit, and it will come back again.

Great model indeed.

Very nice build of a difficult model, good work there.

The Revell kit from 2012-forward if I would choose. The old AMT kit is a lot older and may be the one you have seen.

3D Model Specialities on Shapeways has an AJPE (Alan Jonson Performance Engineering) 500 cui Hemi for modern Nitro cars as well as a Donovan 417 if you want a nostalgia engine, and lots of other neat stuff. TRD Inovations also has some decent parts.

The aluminum colored cover w/four bolts is where the oil filter adapter/housing usually are as it's a separate piece on the FE, and this plate seems to be just a block off plate, behind that plate it's only two oil passages, one comes from the oil pump and goes in to the filter and the other one goes back into the oil gallery inside the block...so it's just like a loop and nothing more fancy than that. Sometimes remote oil filters are used and there are a couple different adapters for that, and they are bolted at the same place as the reguar filter adapter/housing. You can't put an external oil pump at this spot (like on a Mopar 383-440 RB and Hemi) as you don't have any way to drive it, the oil pump on a FE is internal and driven with an axle from the cam shaft and distributor right above it. The Mopar RB oil pump are on the outside of the block and is also driven from the cam shaft and distributor but the axle for the pump goes all the way through the engine block to the outside pump. Here is a picture of the 390 engine I'm rebuilding right now for my 1963½ Galaxie to explain how it looks like behind that block off plate.

I just wonder who they are going to blame when it goes south and an accident has happened with a self driving car...the manufacturer who made the car or the software, or the person in the car...I mean, if the car is self driven none of these parties drove the car when the accident happened...and how will the insurance companys do in such a case...who has responsibillity.

Yes they were appearently available both ways, according to my references it looks like Sox & Martin used the black version on most of their cars. But I understand it's a bit late to change and the build looks fantastic anyway.

Yes BNL intake is slightly better than the old MPC intake but it still doesn't really capture the look of the real thing. The one Mark scratch built is one of the better ones I have seen so far.

Very nice build.