gtx6970 Posted December 11, 2012 Share Posted December 11, 2012 Is there avail a version of the 1964 Ford Galaxie that the hood is NOT molded in with the body (aka promo style ) ??? I have a couple of the old AMT blue printer kits and the hood is molded shut,,, but I would prefer an open hood version if there is one avail with a reasonable effort . Quote Link to comment Share on other sites More sharing options...
Art Anderson Posted December 11, 2012 Share Posted December 11, 2012 Is there avail a version of the 1964 Ford Galaxie that the hood is NOT molded in with the body (aka promo style ) ??? I have a couple of the old AMT blue printer kits and the hood is molded shut,,, but I would prefer an open hood version if there is one avail with a reasonable effort . The quick answer is: No. AMT made the '64 Galaxie 500XL in three kit versions over the years. In 1964, they produced a full detail (as full detail as existed in 1964) of both the hardtop and the convertible. In the mid-1980's, as the first of AMT/Ertl's "Blueprinter" series of kits (marketed to subscribers to the Ertl Blueprinter magazine) was the '64 Galaxie XL500 hardtop, but that used the old promo tooling, which meant having no engine detail, the hood molded one-piece with the body shell. The 3in1 kits have not been seen in stock form since 1964, while the hardtop 3in1 was modified into a Nascar stocker in 1968--and the tooling apparently cannot be restored to stock configuration. Art Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted December 11, 2012 Share Posted December 11, 2012 (edited) I have a dirty but not-too-bad gluebomb '64 Galaxie 500 convertible (open hood) gluebomb I scored with some other stuff a while back, all of it pretty cheap. Seems they might still be out there. As the hood-opening lines are straight on the sides, opening a molded-shut one is straightforward. Edited December 11, 2012 by Ace-Garageguy Quote Link to comment Share on other sites More sharing options...
Scuderia Posted December 11, 2012 Share Posted December 11, 2012 As the hood-opening lines are straight on the sides, opening a molded-shut one is straightforward. That and drop the body on a similar chassis and engine. Will the 60 fit?. Quote Link to comment Share on other sites More sharing options...
retroguy Posted December 11, 2012 Share Posted December 11, 2012 There are 64 Galaxies with opening hoods on ebay... http://www.ebay.com/sch/i.html?_odkw=&_osacat=2580&_catref=1&_trksid=p2045573.m570.l1311&_nkw=64+galaxie&_sacat=2580&_from=R40 Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted December 11, 2012 Share Posted December 11, 2012 That and drop the body on a similar chassis and engine. Will the 60 fit?. Just checked the '60 kit and it's the same semi-perimeter frame as the '64. Also, a cursory web search says both cars are on the same wheelbase (119"), which is what the models look like. Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted December 11, 2012 Share Posted December 11, 2012 (edited) There are 64 Galaxies with opening hoods on ebay... Wow. Anybody know when that Pro-Shop edition came out? Open hood !! http://www.ebay.com/itm/1-25th-AMT-1964-Ford-Galaxie-Hardtop-500-XL-Kit-As-Is-/200861583521?pt=Model_Kit_US&hash=item2ec44888a1 Top one's a 2-fer. One open, one shut, I think. http://www.ebay.com/itm/AMT-Model-Car-Kit-Lot-2-1964-FORD-GALAXIE-500-XL-GALAXIE-500-SPECIAL-ED-/190766631955?pt=Model_Kit_US&hash=item2c6a93cc13 EDIT: The secondary pix show both versions with molded-closed hoods, but the built red Pro-Shop has it open. Interesting. Edited December 11, 2012 by Ace-Garageguy Quote Link to comment Share on other sites More sharing options...
Scuderia Posted December 11, 2012 Share Posted December 11, 2012 (edited) Just checked the '60 kit and it's the same semi-perimeter frame as the '64. Also, a cursory web search says both cars are on the same wheelbase (119"), which is what the models look like. I thought that might work but wasn't sure. I didn't even know the P.S. Kit had a hood and engine. Unless the individual that built that red one did the chassis swap and cut open the hood.. Edited December 11, 2012 by Scuderia Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted December 11, 2012 Share Posted December 11, 2012 (edited) I thought that might work but wasn't sure. I didn't even know the P.S. Kit had a hood and engine. Unless the individual that built that red one did the chassis swap and cut open the hood.. Mmmmm hummm, but the red built one displayed with the PS box has the same molded-in tabs on the fenders at the rear of the hood-opening to support the hood, and the same bosses for the screw-bottom screws in the radiator support panel as my open-hood '64 convertible (at least the tabs wouldn't be there if the hood had been cut open, and the rad-support would have been cut through too, separated from the hood and would not show the clean-lined top that it does). Maybe a first-gen model ended up in a PS box somewhere along the line. Hmmmmm..... Edited December 11, 2012 by Ace-Garageguy Quote Link to comment Share on other sites More sharing options...
Erik Smith Posted December 11, 2012 Share Posted December 11, 2012 That has to be a first release kit in a new box. I would like to have it! I have a first box I bought in a lot sale but it had a 59 Edsel inside Quote Link to comment Share on other sites More sharing options...
gtx6970 Posted December 12, 2012 Author Share Posted December 12, 2012 Thanks all. It confirmed my suspicions . I have a couple of the Blueprinter issues ( hood molded shut) I guess I'll just cut the hood out of it and set the body- interior on a different chassis I want to use a resin thunderbolt / tear drop style hood in it's place. Quote Link to comment Share on other sites More sharing options...
Bartster Posted December 13, 2012 Share Posted December 13, 2012 l have this project started. Haven't opened the hood yet, but it appears the body will work on the '60 chassis with very little "help". Bart Quote Link to comment Share on other sites More sharing options...
Jeff B Posted March 9, 2013 Share Posted March 9, 2013 I see various releases of the AMT '64 Galaxie, and I've always loved the body style and want to buy a kit or 2. Does anybody know if there is a big difference between the: Model King release Millennium release and Pro Shop release? For example, are there differences in decal sheets, mold quality, or custom parts? Quote Link to comment Share on other sites More sharing options...
Mark Posted March 9, 2013 Share Posted March 9, 2013 Only the original annual kits (hardtop and convertible) and the 1968 reissue Daytona Sportsman include an engine and an opening hood. The Daytona Sportsman reissue can be built stock or custom. It was not altered from the annual except for the deletion of the working lights feature. The clear "light transfer" parts were still included. With the addition of two small bulbs and a battery box, the working light feature could be put back in. The 1971 issue Modified Stocker is based on the annual/Daytona Sportsman. The alterations made to create the Modified Stocker are extensive and most likely irreversible. The 1964 promotional models were produced from different tooling than was used for the kits, though many parts will interchange. The promotional model interior is simpler however, not having a separate rear seat like the full detail kits. The promo model was issued in unassembled form around 1967 as a Craftsman Series kit. The Blueprinter, Pro Shop, Millennium Series, and Model King '64 Galaxie kits are all based on the promo model. Being based on a promotional, it has no engine, opening hood, or optional parts. After the Blueprinter issue but before the Pro Shop issue, the Galaxie was issued as a pre-assembled "retro promo". A number of changes were made, and several parts were retooled, most notably the wheel covers. Model King commissioned reissues of both '64 Galaxies: the stock-only ex-promotional, and the Modified Stocker. The Modified Stocker has a number of parts "unblocked" in the tooling that were not included in its first issue (because the Modified Stocker did not need them). These include the stock air cleaner, stock oil pan, and stock wheel covers. The Modified Stocker reissue has the molded-in stock dual exhaust restored to the chassis also. This was done when AMT/Ertl first reissued the '63 Galaxie in the mid-Eighties (apparently the '63 and '64 used the same piece, and the exhaust was needed for the stock '63). If you want chassis and engine detail that is like that in the annual kits, the Modified Stocker reissue has all of the parts plus the stock wheel covers from the annual kit. If you want upgraded detail, you may want to go with the chassis and engine from the newer '60 Starliner kit and make the changes needed to correct the differences between '60 and '64. Quote Link to comment Share on other sites More sharing options...
Luc Janssens Posted March 10, 2013 Share Posted March 10, 2013 having played with my pro-shop issue, I seem to remember that if you're trying to cut out the hood, you'll see that where the fenders meet the cowl/ A-pillars isn't exactly the same left to right, like the hood opening isn't centered. You may want to look into that especially when you're thinking about scribing a parting line between cowl and fender. Luc Quote Link to comment Share on other sites More sharing options...
horsepower Posted March 11, 2013 Share Posted March 11, 2013 check out item number 230941075144 that's one of the original release "Annuals" with the open hood & engine detail. Quote Link to comment Share on other sites More sharing options...
Edsel-Dan Posted March 11, 2013 Share Posted March 11, 2013 I have the ProShop & Model-King issues. Only differences are box art & decals. ProShop only had 1966! License plates. M-K kit has a large sheet. I need to dig it out and look at it again!! Knowing they altered the tooling Before the "BluePrinter Promo issue, but Before the BluePrinter Kit issue, I will have to try to get one nof that kit to complare with the Built painted kit I got as a Promo. I Know it to be a kit as it is White underneath the Aqua! Promos were Molded in the color not painted. Quote Link to comment Share on other sites More sharing options...
Jeff B Posted May 8, 2013 Share Posted May 8, 2013 Thanks for the great responses Luc, Mark, horsepower and Edsel-Dan!! Quote Link to comment Share on other sites More sharing options...
ToyLvr Posted May 9, 2013 Share Posted May 9, 2013 Bill: Why can't you work on something "uncomplicated" for a change??? ;-) I remember reading an article in one of the model mags a few years ago about someone opening the hood on a '63 Galaxie promo. I'm pretty sure that the author used the chassis from the new-tool '60 Ford Starliner (as Mark mentioned above). I don't think it required a whole lot of modification, and I bet it would work fine for a conversion on your '64. I'll see if I can locate the article in my archives and post the info. Mike Quote Link to comment Share on other sites More sharing options...
gtx6970 Posted May 9, 2013 Author Share Posted May 9, 2013 Whats the fun in that ? it wouldn't be modeling if one didn't have to think about it a bit. I did pick up a 60 Starliner chassis recently on a trade so this project is in the near future, just haven't decided if i'll do a 63 or a 64 ( got a couple of each ) pm replied btw Bill: Why can't you work on something "uncomplicated" for a change??? ;-) Quote Link to comment Share on other sites More sharing options...
fastram Posted May 15, 2013 Share Posted May 15, 2013 An easy way to build the 64 and make it a (64 style) full detail is to use the Blue Printer Body with the 63 Galaxie kit. The hood can be cut open on the 64 and the interior can be modified using the 64 and 63 tubs. The chassis is a drop in. Quote Link to comment Share on other sites More sharing options...
Casey Posted January 21, 2019 Share Posted January 21, 2019 (edited) On 3/9/2013 at 12:37 PM, Mark said: Only the original annual kits (hardtop and convertible) and the 1968 reissue Daytona Sportsman include an engine and an opening hood. The Daytona Sportsman reissue can be built stock or custom. It was not altered from the annual except for the deletion of the working lights feature. The clear "light transfer" parts were still included. With the addition of two small bulbs and a battery box, the working light feature could be put back in. Edited February 9, 2019 by Casey Quote Link to comment Share on other sites More sharing options...
ChrisBcritter Posted January 21, 2019 Share Posted January 21, 2019 Direct upload in case the Photobucket image disappears after a couple seconds: (Anyone else have that problem?) Quote Link to comment Share on other sites More sharing options...
Ron Hamilton Posted January 21, 2019 Share Posted January 21, 2019 I am lucky that I didn't sell off my unbuilt annual hardtop and Converible. I really like 64 Ford's. Quote Link to comment Share on other sites More sharing options...
Bob Ellis Posted January 22, 2019 Share Posted January 22, 2019 20 hours ago, Ron Hamilton said: I am lucky that I didn't sell off my unbuilt annual hardtop and Converible. I really like 64 Ford's. The 1964 fords are beautiful. To me, much nicer fastback than 1965 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.