customline Posted November 29, 2022 Share Posted November 29, 2022 (edited) I want to apologize right up front. I found this photo while searching for ideas for my Revell '40 coupe. If it's yours, I'm sorry but I need it to illustrate something. I knew I wanted to chop it a bit but there are many different looks for this car and well, you know.....anyway, I thought it might be interesting to somebody ( you can remain anonymous 🤐 , Michael ) to see the following photos of the steps I took to get a fair chop. It's not finished, it's rough.... but I wanted to get it out there. Maybe I'll finish this one. We'll see. The first picture is one way to do this chop. Not the way I would. I'm not saying my way is right but it worked for me (this time) and, because I am learning as I go, this is in no way a tutorial. Edited November 29, 2022 by customline Fixed a goof Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 This is how I started. Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 Because the C pillars don't align well after removing the section, I added some .020 sheet scrap to the bottoms so the top had a landing and gluing surface. Some .015 strips were added inside the B pillars as well. Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 The A pillars were sectioned and the roof returned to its proper, lower, place 🙂. It's Bondo time! Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 Looks awfully messy, doesn't it? I love Bondo. This is as far as I got today. Now I need to decide to add back the drip rail or not. It changes the whole look. For this mild chop, I am leaning towards the drip rail. I dunno. Lots of work still ahead. 6 Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted November 29, 2022 Share Posted November 29, 2022 It's definitely working. Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 26 minutes ago, Ace-Garageguy said: It's definitely working. The nice thing about the '40 is the smooth radius of the window moldings. Makes it easier to get a clean chop. This kit came in a bag, bought off Ebay. It's the Street Rod version. No telling where it's going yet. The flathead will not be under the hood. 😉. I have other plans for that. Quote Link to comment Share on other sites More sharing options...
NOBLNG Posted November 29, 2022 Share Posted November 29, 2022 Looks purdy good to me!👍 Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 2 minutes ago, NOBLNG said: Looks purdy good to me!👍 Thank you, Greg. I enjoyed doing it. The big question now is " Do I keep the drip rail ?" Gotta do more research (that's what I call looking at pictures of hot rods) Quote Link to comment Share on other sites More sharing options...
NOBLNG Posted November 29, 2022 Share Posted November 29, 2022 2 minutes ago, customline said: Thank you, Greg. I enjoyed doing it. The big question now is " Do I keep the drip rail ?" Gotta do more research (that's what I call looking at pictures of hot rods) If it was me, I would try to add it back on. Easy to sand it back off if it gets messed up or doesn’t look right. JMO. Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 1 minute ago, NOBLNG said: If it was me, I would try to add it back on. Easy to sand it back off if it gets messed up or doesn’t look right. JMO. Yeah, I agree. I just got some Plastruct triangle rod for another job but it may work on this one. My worry is trying to glue it to the Bondo and CA surfaces on the C pillar. On styrene I will bond it with "welder" but that may not work on polyester. I need to test that. It'll be a tedious operation. Thinking about replacing the running boards with side exhaust from '68 'Vette. Hmmmm....... Quote Link to comment Share on other sites More sharing options...
beeRS Posted November 29, 2022 Share Posted November 29, 2022 Great work on that roof chop. I have an in-progress that looks nearly identical to this. Great minds must think alike 😀. I did my chop a differently to yours and the one in the opening post. I cut the rear screen along with the C pillars and layed them forward. There must be as many ways to chop a top as there are builders. Now I’m m intrigued to see what you do about the drip rail. Quote Link to comment Share on other sites More sharing options...
Zippi Posted November 29, 2022 Share Posted November 29, 2022 The chop on the 40 Coupe is looking pretty good. Quote Link to comment Share on other sites More sharing options...
dragcarz Posted November 29, 2022 Share Posted November 29, 2022 Clean chop! Looks great! Quote Link to comment Share on other sites More sharing options...
lucky 130 Posted November 29, 2022 Share Posted November 29, 2022 I'm doing a similar chop on a VW and have run into some minor issues, but nothing too awful. I agree Bondo works. I like where you are headed, can't wait for more. Model on. Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 6 hours ago, beeRS said: Great work on that roof chop. I have an in-progress that looks nearly identical to this. Great minds must think alike 😀. I did my chop a differently to yours and the one in the opening post. I cut the rear screen along with the C pillars and layed them forward. There must be as many ways to chop a top as there are builders. Now I’m m intrigued to see what you do about the drip rail. Yeah, the drip rails....I picked up some .030" triangle rod for a side trim mod on a future project that may work for this but will ,no doubt, be testing my resolve. The key to a great custom (kustom) is that it looks like the factory built it; it would have drip rails. In the case of the Ford coupe, the drip rail defines and accentuates the fluid curves of the whole design. With the drip rails shaved off, the coupe takes on a lead-sled look and and my mild chop won't work well in that genre. This is a more contemporary look. My challenge is remaining consistent throughout the overall look. The right wheel/tire combo, bumpers, paint....I still don't have a firm plan yet. I'm entertaining all ideas and comments. The photo below was found in the ether and appears to be a photo-shopped study that the builder of this 1:1 was using to plan his build. I like it a lot. It totally works. Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 5 hours ago, Zippi said: The chop on the 40 Coupe is looking pretty good. 4 hours ago, dragcarz said: Clean chop! Looks great! Thanks, Bob and Roger. Wish me luck ☺️ Quote Link to comment Share on other sites More sharing options...
customline Posted November 29, 2022 Author Share Posted November 29, 2022 3 hours ago, lucky 130 said: I'm doing a similar chop on a VW and have run into some minor issues, but nothing too awful. I agree Bondo works. I like where you are headed, can't wait for more. Model on. A VW Beetle? That's a chop I would not attempt. The 1:1s I've seen look a bit awkward. The complicated nature of the C pillar/hood scares me off. I have given serious consideration to attempting a chop of the Moebius '47 Aero Sedan, but that's about as difficult as I'm willing to go for now. You are welcome to post pix of your VW here, and that goes for anyone working on a chop. Or maybe post a link. I'm here to learn. Below is a chop I did on the AMT '41 Plymouth Coupe. 2 Quote Link to comment Share on other sites More sharing options...
TransAmMike Posted November 29, 2022 Share Posted November 29, 2022 Wow, thats quite the adventure Jim with a great result. 👌 Quote Link to comment Share on other sites More sharing options...
gman Posted November 29, 2022 Share Posted November 29, 2022 2 hours ago, customline said: A VW Beetle? That's a chop I would not attempt. The 1:1s I've seen look a bit awkward. The complicated nature of the C pillar/hood scares me off. I have given serious consideration to attempting a chop of the Moebius '47 Aero Sedan, but that's about as difficult as I'm willing to go for now. You are welcome to post pix of your VW here, and that goes for anyone working on a chop. Or maybe post a link. I'm here to learn. Below is a chop I did on the AMT '41 Plymouth Coupe. That chop on the Plymouth sure changes its attitude- looks downright angry (and nice color choice). Quote Link to comment Share on other sites More sharing options...
customline Posted November 30, 2022 Author Share Posted November 30, 2022 6 hours ago, gman said: That chop on the Plymouth sure changes its attitude- looks downright angry (and nice color choice). The Plymouth was twice as much fun as the Ford. It started the same way but there were a few "issues". So, yeah, 😠 it's a reflection of my state of mind, apparently 🥴 . the color is a Boyd's. Looks fantastic out in the sun. Quote Link to comment Share on other sites More sharing options...
customline Posted November 30, 2022 Author Share Posted November 30, 2022 (edited) Late Edition..... Got a little more done tonight. Modified the front spring by removing the retainer so the spring fit further inside the cross member, which was opened up a bit. There was a significant gain in drop. I may try to get the front wheels inboard a bit more by trimming the wheel "hubs". Cleaned up parting lines and eliminated the bumper grommets and filled the holes, front and rear. Added rear tag recess. Drilled locating holes and removed the door and trunk handle and tail light locators to facilitate micro-polishing. Removed gas cap boss. Started chassis construction. The plan, for now, is using the T-Bird engine from the '34 pickup kit (dechromed, of course. ) or possibly a small block ford that's around here somewhere 🤔. About that second pic....it won't be that low.....unless I channel it too 😉 This last picture shows what happens when you install the rear axle incorrectly (upside-down) Edited November 30, 2022 by customline Rearranging photos 3 Quote Link to comment Share on other sites More sharing options...
bluestringer Posted November 30, 2022 Share Posted November 30, 2022 Looks great Jim. Nice work. Looking forward to the finished build. Quote Link to comment Share on other sites More sharing options...
customline Posted November 30, 2022 Author Share Posted November 30, 2022 1 minute ago, bluestringer said: Looks great Jim. Nice work. Looking forward to the finished build. From here on in, it's all about the weather. I paint outdoors. Thanks, James. Maybe I'll get some primer on it soon. 1 Quote Link to comment Share on other sites More sharing options...
Plowboy Posted November 30, 2022 Share Posted November 30, 2022 Your chop work looks good Jim! I built this kit around three years ago. I converted it to a three window, gave it a three and a half inch chop and three inch section. The only issue I had with it was getting the rear wheels centered. First mockup, it was 3 mms too forward. I moved the crossmember back 3mms. It was 1.5 mms too far back! Moved the crossmember forward 1.5 mms and finally got it right. What I learned from that ordeal was that the placement of the rearend is very sensitive to the angle of the pinion. Some members reported the same issue. Some reported no issue. It's definitely something to get worked out beforehand! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.