trogdor Posted January 7, 2012 Posted January 7, 2012 (edited) I recently started to build the model I've always wanted. Because there is no commercial offering, I'm stuck with making my own. I'm using the back half of the AMT 55 corvette and making the front myself. I sent a message to Peter Lombardo and he agreed to vacuum form it once I have the form done. Just a short list of changes to the corvette to make this work rear license plate recess has to be lowered remove corvette bodyside mouldings add thin styrene sheet to rear deck re-work rear fins for tail light details fill corvette gas tank door fill cowl vent remove wipers re-scribe door panels and rear deck panel lines New scratch work to do most all of the interior needs to be scratch built intake manifold need to be scratch built All panels from the firewall forward need to be made The real car I will say this, it was a lot harder than I thought it would be to get to this point. I had only one dimension to work with, that was the wheel base of 100 inches. All my drawings and measurements are based of that, and the width of the corvette body. I've got my work cut out for me. As a former Seabee, I'm reminded of this phrase the difficult we do immediately, the impossible takes a bit longer. ... I've never done anything like this, but hey that never stopped me from doing anything else in life. Here is more progress on the mold for the front. I had to shoot some primer on it because the lines from the woodgrain were throwing me off a bit I'm just about ready to send the mold to peter. Let me know what you think. I've been staring at this thing until I'm cross eyed. so if something looks off, let me know. The real car again. (The raised portion down the middle of the hood will be added later with sheet styrene) Edited January 7, 2012 by trogdor
oldnslow Posted January 7, 2012 Posted January 7, 2012 Gorgeous car, looks like you have a great start, this will be fun to watch.
dc10oiller Posted January 7, 2012 Posted January 7, 2012 Holy snappin' arses! This is going to be brilliant.
Peter Lombardo Posted January 7, 2012 Posted January 7, 2012 Great looking front end....I am really impressed.....man, this is going to fun. I am looking forward to contributing, even in a small way, to your adventure.....go get'em.
jeffs396 Posted January 7, 2012 Posted January 7, 2012 Very cool Rick! Great work so far. Can't wait to see more!
Custom Mike Posted January 7, 2012 Posted January 7, 2012 Very ambitious Rick, and it looks like you're off to a great start! I can't wait to watch this one come together!
4bangen Posted January 7, 2012 Posted January 7, 2012 never thought about using wood to make molds. thanks for the tip, I'm a buick nut, so you know I'm watching!
mrm Posted January 7, 2012 Posted January 7, 2012 This thing is crazy. Very cool and great work so far. I will also be following this for sure.
Austin T Posted January 7, 2012 Posted January 7, 2012 Was a real car ever made or just a prototype?I have fallen In love with this and this is the first time I have seen it,Lol.Whats under the hood?A Wildcat V-8?
Chuck Most Posted January 7, 2012 Posted January 7, 2012 Nice seeing this dragged back to the front burner, Rick! You know I'll be tagging along.
trogdor Posted January 7, 2012 Author Posted January 7, 2012 Was a real car ever made or just a prototype?I have fallen In love with this and this is the first time I have seen it,Lol.Whats under the hood?A Wildcat V-8? Austin, this was a one off concept car built by Buick. The engine was a 322 cubic-inch 220 bhp Buick V8 with four side-draft carburetors and dual exhausts. It was design by Harley Earl who was perhaps the most influential designer GM ever had. He also designed the Buick Y Job. The following is copied from the GM heritage center website : The 1954 Buick Wildcat II concept, designed by Harley Earl’s design team, made its public debut at the 1954 General Motors Motorama in New York City. Built of fiberglass and mounted on a 100-inch wheelbase, the 1954 Wildcat featured radical new front fender styling that exposed the underside of the fender and the chrome plated front-end suspension. The fenders were lined with large chrome panels containing air scoop louvers. Buick Skylark wire wheels were used. The car was only 170-inches long and 35-inches high at the cowl. Headlamps were mounted on the cowl with parking and directional signal lights on the front end underneath the fender shroud. Bumpers were shaped with two big torpedo-like guards; know in those days as “Dagmar” bumper guards, a name taken after a sexy celebrity with a good size bosom. Wildcat II was powered with a standard 322 C.I.D. V8 engine boosted to 220 horsepower through the use of four carburetors. Originally the car was painted a bright blue with a white leather interior but later was repainted dark tan with a two-tone tan leather interior. The Wildcat II now resides at the Alfred P. Sloan Museum in Flint, Michigan where it was restored to its original bright blue finish. The 1954 Wildcat II was the second of three concept cars introduced in consecutive years to wear the Wildcat badge.
Dave42 Posted January 7, 2012 Posted January 7, 2012 Wow, nice job on that front end. I struggle to bash two plastic kits together. Later,
DumpyDan Posted January 7, 2012 Posted January 7, 2012 This was very interesting to watch and will be waiting for more, if your this good with wood what could you do with plastic. Scary I'd say. Keep it coming please.
MikeMc Posted January 7, 2012 Posted January 7, 2012 With your woodworking talents Rick....I'm not surprised....well OK...I thought you would carve the whole thing! Keep it coming!!
jaymcminn Posted January 7, 2012 Posted January 7, 2012 Looking forward to this- that chrome trim up front is pretty intimidating, though!
kennb Posted January 7, 2012 Posted January 7, 2012 I have been wanting to do this one too along with a few others based on the early Corvette. I have the Corvette ordered so I guess I will go with one of the other variations....Very nice start and looking forward to the finished product. KennB
MrObsessive Posted January 15, 2012 Posted January 15, 2012 Excellent wood work! That's something I could never get the hang of! Keep it going!!
trogdor Posted January 15, 2012 Author Posted January 15, 2012 Thanks Bill, I'd be willing to trade my woodworking skills for your modeling skills.
Wagoneer81 Posted January 15, 2012 Posted January 15, 2012 I like it! I'd like a couple of those front ends, myself...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now