2002p51 Posted February 12, 2019 Posted February 12, 2019 Well, the finished product turned out to be pretty disappointing. but more on that in a minute. First a little background on the real car. The Grand Sport project was mostly a skunk works type of effort as GM was under a self imposed racing ban. But in 1964 the suits at Chevrolet had finally had enough and said; "No, seriously, this has to stop." and they pulled the plug. Three of the five cars built were sold to privateers. The subject of this model, chassis #005, was sold to Jim Hall. Since Hall was so busy with preparations of his own Chaparral the car was shipped to Roger Penske's shop in Pennsylvania to be prepared for the Sebring 12 hour race where Penske and Hall would share the driving. In spite of inferior handling the Penske/Hall Grand Sport was able to use its power advantage to take first in class and 18th overall against a field of potent Cobras and Ferrari prototypes. Before we go any farther, if you would like to see some of the work that went into this model you can click here: http://www.modelcarsmag.com/forums/topic/139757-new-project/ In that thread I mentioned that the chassis had quite a bit of twist in it. I was able to get 99% of that out without doing any damage and thought it was good. During final assembly it was difficult to get the chassis to touch any of the bottom of the car well enough to get any glue to hold. I thought I had it once but, after giving the glue time to dry, I picked the model up and the chassis just dropped off. So I got a little more aggressive and finally got something to grab and hold. But this time, when I turned the model over and placed it on the bench, the twist was back! Not quite as much but the right front tire was back in the air again. You'll notice in the photos that the hood also doesn't fit very well and I think that's a product of this newly induced twist. Rats! Speaking of the hood, notice what looks like tape covering the louvers. This is evident in the photos that are in the Corvette Grand Sport book. It seems they covered the hood to prevent the Florida rain from getting into the engine compartment. Accurate Miniatures provided some very nice stickers to replicate this look although they are not mentioned anywhere in the instruction sheet. Unfortunately, possibly due to age, the edges didn't stick too well and I had to use a microbrush and apply a little Krystal Klear all around the edges to get them to stay down. I also scratched the paint a little with my thumbnail trying to get the edges to stay down. They're still not perfect but then, neither was the tape job on the real car. So, all in all, it is disappointing when all of the effort and work that's required to build this model all goes south during final assembly. Especially in spite of numerous test fittings. Things are so much harder to fix once everything is painted and finished. So there it is. At least I now have the sister car to the Mecom prepared chassis #004 that was driven in the '64 Sebring by A.J. Foyt. But this one will never see any sort of show table for sure.
afx Posted February 12, 2019 Posted February 12, 2019 The frame twist isn't evident in the photos. Really like the paint sheen - not unrealistically glossy.
MrObsessive Posted February 12, 2019 Posted February 12, 2019 Drew, that looks mighty good from where I sit! If you hadn't mentioned any troubles I would have thought nothing of it! And yes, the finish on that is perfect for that era of race car.
espo Posted February 12, 2019 Posted February 12, 2019 I followed your build on this and it's a shame so much of your hard work on the chassis goes unseen. Turned out perfect and I like the knock-off wheels.
2002p51 Posted February 12, 2019 Author Posted February 12, 2019 36 minutes ago, afx said: Really like the paint sheen - not unrealistically glossy. Thanks to you and Bill Geary for noticing that. If you know my writings, you know super glossy race cars is a favorite pet peeve of mine.
Dave Van Posted February 12, 2019 Posted February 12, 2019 You still made it look good!!! As I commented on the build thread there are two versions of the kit......the 2nd version had some refinements.....sounds like you got a 1st version maybe. Still a build I'd be happy to show!!
2002p51 Posted February 12, 2019 Author Posted February 12, 2019 Dave, thanks for the compliment. I've still got one more of these kits. Not sure what I'll do with it. I've got two resin conversion bodies, one is a roadster and the other is the early prototype. So there is a possibility there.
Bill J Posted February 12, 2019 Posted February 12, 2019 Looks like a fine outcome to me. Great work on the Corvette GS, the best looking 'vette of all.
Snake45 Posted February 12, 2019 Posted February 12, 2019 2 hours ago, MrObsessive said: Drew, that looks mighty good from where I sit! If you hadn't mentioned any troubles I would have thought nothing of it! And yes, the finish on that is perfect for that era of race car. What he said. Very clean looking build!
James2 Posted February 12, 2019 Posted February 12, 2019 I think it looks pretty nice myself, paint, side marker lights, wheel detail and decals add to the authenticity value. I have four of these kits, two are under construction, Chassis #003 and 005. I have not seen any twist in my frames, but I noticed you filled the chanels in the frame tubes as many of us have done. Could the twist could have happened then?
2002p51 Posted February 12, 2019 Author Posted February 12, 2019 Just now, James2 said: I have not seen any twist in my frames, but I noticed you filled the chanels in the frame tubes as many of us have done. Could the twist could have happened then? I suppose anything like that is possible. It never occurred to me to check it for straight before I ever started. So, my bad.
Jim N Posted February 12, 2019 Posted February 12, 2019 Looks very nice! Great work with the paint and decals.
Phildaupho Posted February 12, 2019 Posted February 12, 2019 This Chaparral white version of the Grand Sport has always been my favorite and the one I would build if I ever get around to. Your model certainly looks very nice in the photos. I was never sure if the hood on this version was solid or tapped so thanks for clearing that up. I do believe it may of had a scoop rather than the vents.
Gramps46 Posted February 12, 2019 Posted February 12, 2019 Looks display worthy to me. I am in the same camp with you and the others when in comes to race car shine, or lack there of, in that era. Well done and thanks for sharing it with us.
Dave Van Posted February 12, 2019 Posted February 12, 2019 4 hours ago, 2002p51 said: Dave, thanks for the compliment. I've still got one more of these kits. Not sure what I'll do with it. I've got two resin conversion bodies, one is a roadster and the other is the early prototype. So there is a possibility there. AM designed a roadster body and started tooling.......but it never made it to test shot stage.....Oh the plans AM had for this and other all new tools.....
2002p51 Posted February 12, 2019 Author Posted February 12, 2019 16 minutes ago, Phildaupho said: This Chaparral white version of the Grand Sport has always been my favorite and the one I would build if I ever get around to. Your model certainly looks very nice in the photos. I was never sure if the hood on this version was solid or tapped so thanks for clearing that up. I do believe it may of had a scoop rather than the vents. There is one photo of the car in the Grand Sport Corvette book that shows the car without the tape and it definitely has the same type of vents as the blue Mecom car.
2002p51 Posted February 12, 2019 Author Posted February 12, 2019 3 minutes ago, Dave Van said: AM designed a roadster body and started tooling.......but it never made it to test shot stage.....Oh the plans AM had for this and other all new tools..... Would've been interesting to see for sure. The resin bodies I have were done by Cheez Cast. No idea how long ago I got them but I don't think Cheez Cast is around anymore.
afx Posted February 12, 2019 Posted February 12, 2019 HRM did a very nice roadster trans-kit, I can post pictures of the kit if you like Drew.
2002p51 Posted February 12, 2019 Author Posted February 12, 2019 Just now, afx said: HRM did a very nice roadster trans-kit, I can post pictures of the kit if you like Drew. Yea sure, I'd love to see it.
Phildaupho Posted February 12, 2019 Posted February 12, 2019 6 minutes ago, 2002p51 said: There is one photo of the car in the Grand Sport Corvette book that shows the car without the tape and it definitely has the same type of vents as the blue Mecom car. Yes I agree. I had not looked at The Grand Sport book for a very long time. What I was really meaning is that it did not have the side louvers like the hood in the kit representing other versions of the GS. I have a resin hood from Historic Racing Miniatures called a Nassau Hood which is definitely like the Mecom car.
Dann Tier Posted February 12, 2019 Posted February 12, 2019 8 hours ago, afx said: The frame twist isn't evident in the photos. Really like the paint sheen - not unrealistically glossy. I agree 100%!!....excellent Build!!!
afx Posted February 12, 2019 Posted February 12, 2019 4 hours ago, 2002p51 said: Yea sure, I'd love to see it. Here you go. The casting looks like injection molded parts. The kit includes the 1966 spec big block 427 engine an American Racing wheels used by Penske/Wintersteen.
tbill Posted February 13, 2019 Posted February 13, 2019 That sir is a fine looking build! Nothing to be ashamed of there .
Hotrod 97 Posted February 13, 2019 Posted February 13, 2019 Looks fine to me! Great job on the finish!
2002p51 Posted February 13, 2019 Author Posted February 13, 2019 (edited) Thanks for posting that conversion kit, AFX. Looks like nice stuff. Edited February 13, 2019 by 2002p51
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now