2zwudz Posted April 1, 2020 Share Posted April 1, 2020 What method do you like best for decanting spray cans? Quote Link to comment Share on other sites More sharing options...
935k3 Posted April 1, 2020 Share Posted April 1, 2020 Spray right into jar by regulating trigger pressure and holding jar at an angle. Quote Link to comment Share on other sites More sharing options...
Miatatom Posted April 1, 2020 Share Posted April 1, 2020 I'm going to do a video sometime with my method. It involves using a valve for tapping into a water line to hook to a refrigerator and short length of copper tubing and two hose clamps. It's been discussed on this forum, I think. Quote Link to comment Share on other sites More sharing options...
NOBLNG Posted April 1, 2020 Share Posted April 1, 2020 (edited) I bought a bunch of large plastic straws at the Dollar Store. They are close to 1/2” diameter. I cut them in half and spray into it with the other end held in the paint jar. I used to spray into a funnel but then I had to clean it. The straws I just toss. I don’t necessarily wait for it to outgas either. I figure...where would that gas be if I was spraying it directly on the model? Edited April 1, 2020 by NOBLNG Quote Link to comment Share on other sites More sharing options...
GeeBee Posted April 1, 2020 Share Posted April 1, 2020 I've been doing this way for years without any problems, put a small pin hole at the top of the can, once the gas has escaped, cut the top off and left to de-gas for about 30 minutes, then pour the contents into a glass bottle. Quote Link to comment Share on other sites More sharing options...
DPNM Posted April 1, 2020 Share Posted April 1, 2020 9 hours ago, 935k3 said: Spray right into jar by regulating trigger pressure and holding jar at an angle. The same way I've been doing it for years. Just have to know when to stop. Before it starts to splash out. Quote Link to comment Share on other sites More sharing options...
Mike 1017 Posted April 1, 2020 Share Posted April 1, 2020 Cheap and easy. After flushing with thinner. Flush the nozzle with water Quote Link to comment Share on other sites More sharing options...
peteski Posted April 1, 2020 Share Posted April 1, 2020 (edited) No explanation needed here. Being a hoarder sometimes pays off. Edited April 1, 2020 by peteski Quote Link to comment Share on other sites More sharing options...
James2 Posted April 1, 2020 Share Posted April 1, 2020 This^^^^^, I make my own using leftover scrap styrene tubing .... Quote Link to comment Share on other sites More sharing options...
BigTallDad Posted April 1, 2020 Share Posted April 1, 2020 17 hours ago, 2zwudz said: What method do you like best for decanting spray cans? I know you're a newbie, but you're asking questions that have already been answered numerous times. You might want to do some research before you ask your next question. Here's a start http://www.modelcarsmag.com/forums/topic/79627-how-do-i-search-for-answers-already-posted-here/ Quote Link to comment Share on other sites More sharing options...
64Comet404 Posted April 2, 2020 Share Posted April 2, 2020 21 hours ago, Miatatom said: I'm going to do a video sometime with my method. It involves using a valve for tapping into a water line to hook to a refrigerator and short length of copper tubing and two hose clamps. It's been discussed on this forum, I think. This is the method I use. Have never had an issue with removing the paint from the can. I don't bother with the tubing, but use the valve to slowly release the pressure, and pour the paint into a container after opening the can. Quote Link to comment Share on other sites More sharing options...
Roadrunner Posted April 2, 2020 Share Posted April 2, 2020 Some mighty cool ideas here. Thanks, fellas. Odd perhaps, but I remember as a kid opening up empty spray bombs to get the metal ball inside, as they made great nose weights for model aircraft. Quote Link to comment Share on other sites More sharing options...
High octane Posted April 2, 2020 Share Posted April 2, 2020 I've been decanting paint from spray cans for many years simply by warming up the can in warm water, shaking it and spraying on model car bodies and parts. This method works great for me, as I get really nice finishes with metallics, candies, solids, clears, etc. Even works great when painting two and three tone paint jobs as well. No mess, no fuss, no adjustments, no water traps, no noisy compressor, no air pressure or needle problems, etc. Quote Link to comment Share on other sites More sharing options...
peteski Posted April 2, 2020 Share Posted April 2, 2020 45 minutes ago, High octane said: No mess, no fuss, no adjustments, no water traps, no noisy compressor, no air pressure or needle problems, etc. . . . no control of the paint viscosity, nozzle opening size, or air pressure. Once I got an airbrush, I never looked back. I still use spray cans for some jobs around the house or car. But whatever works for you Nick. There will always be 2 kinds of modelers in this world: ones who use airbrushes and ones who don''t. Just like there are people who go through life eating hamburgers without ever trying a nice steak. Just giving you hard time Nick - like I said "whatever works for you". Quote Link to comment Share on other sites More sharing options...
Mike 1017 Posted April 2, 2020 Share Posted April 2, 2020 8 hours ago, peteski said: . . . no control of the paint viscosity, nozzle opening size, or air pressure. Once I got an airbrush, I never looked back. I still use spray cans for some jobs around the house or car. But whatever works for you Nick. There will always be 2 kinds of modelers in this world: ones who use airbrushes and ones who don''t. Just like there are people who go through life eating hamburgers without ever trying a nice steak. Just giving you hard time Nick - like I said "whatever works for you". Or putting ketchup on a hotdog Quote Link to comment Share on other sites More sharing options...
Rodent Posted April 2, 2020 Share Posted April 2, 2020 12 hours ago, peteski said: . . . no control of the paint viscosity, nozzle opening size, or air pressure. Once I got an airbrush, I never looked back. I still use spray cans for some jobs around the house or car. But whatever works for you Nick. There will always be 2 kinds of modelers in this world: ones who use airbrushes and ones who don''t. Just like there are people who go through life eating hamburgers without ever trying a nice steak. Just giving you hard time Nick - like I said "whatever works for you". I for one enjoy a really good hamburger almost as much as a nice steak. Quote Link to comment Share on other sites More sharing options...
James2 Posted April 2, 2020 Share Posted April 2, 2020 21 hours ago, BigTallDad said: I know you're a newbie, but you're asking questions that have already been answered numerous times. You might want to do some research before you ask your next question. Here's a start http://www.modelcarsmag.com/forums/topic/79627-how-do-i-search-for-answers-already-posted-here/ I know you’ve seen here for some time, but your not the forum police. Quote Link to comment Share on other sites More sharing options...
2zwudz Posted April 2, 2020 Author Share Posted April 2, 2020 (edited) 2 hours ago, James2 said: I know you’ve seen here for some time, but your not the forum police. Thank you!! I’ve never seen him help anyone since I’ve been here! Edited April 2, 2020 by 2zwudz Quote Link to comment Share on other sites More sharing options...
peteski Posted April 2, 2020 Share Posted April 2, 2020 (edited) 9 hours ago, Mike 1017 said: Or putting ketchup on a hotdog LOL! I actually like (brown) mustard, onions, sauerkraut, and . . . ketchup. Chili dogs (no cheese) with onions also work for me. Edited April 2, 2020 by peteski Quote Link to comment Share on other sites More sharing options...
2zwudz Posted April 2, 2020 Author Share Posted April 2, 2020 (edited) 47 minutes ago, peteski said: Wow, this social separation, and being stuck at home is certainly making us all really edgy, and angry! We all seem to have "problem socially" nowadays. BTW, I agree with Ray's sentiment - look it up before asking - you will likely find the answer. Mark, you are perfect example of a new member who could benefit from a little forum search before asking for something. There! I said it! Kill me now! Most of the time I do. This time I didn’t! ????. Its still good to ask questions and build relationships. Edited April 2, 2020 by 2zwudz Quote Link to comment Share on other sites More sharing options...
shoopdog Posted April 3, 2020 Share Posted April 3, 2020 On April 1, 2020 at 10:49 PM, High octane said: I've been decanting paint from spray cans for many years simply by warming up the can in warm water, shaking it and spraying on model car bodies and parts. This method works great for me, as I get really nice finishes with metallics, candies, solids, clears, etc. Even works great when painting two and three tone paint jobs as well. No mess, no fuss, no adjustments, no water traps, no noisy compressor, no air pressure or needle problems, etc. This method has worked the best for me also Nick! Quote Link to comment Share on other sites More sharing options...
2zwudz Posted April 3, 2020 Author Share Posted April 3, 2020 2 hours ago, shoopdog said: This method has worked the best for me also Nick! How long do you soak the can in warm water??? Quote Link to comment Share on other sites More sharing options...
High octane Posted April 3, 2020 Share Posted April 3, 2020 1 hour ago, 2zwudz said: How long do you soak the can in warm water??? I use a pot with warm water in it, put the can in it and cover it in case of an explosion, which has never happened to me. I set a timer for about 6 minutes and then remove the can, dry it, shake it, and spray. If I need another coat or two I repeat the process with 20 minute intervals. Other guys may do this differently but this is how I do it and it seems to work. Remember it is warm water and not extremely hot water. PIC.................................................................... Quote Link to comment Share on other sites More sharing options...
Cornpatch Posted April 3, 2020 Share Posted April 3, 2020 got to go with Nicks way---works really good for me---except I shake the can before I put it in the warm water and again when I take it out of the water. Quote Link to comment Share on other sites More sharing options...
Pete J. Posted April 3, 2020 Share Posted April 3, 2020 On 4/1/2020 at 6:38 PM, 64Comet404 said: This is the method I use. Have never had an issue with removing the paint from the can. I don't bother with the tubing, but use the valve to slowly release the pressure, and pour the paint into a container after opening the can. I've used a similar process. I machined this piece some time ago and it is less hassle than all the clamps and valve. I can also make the hole large enough to get a pipet of thinner in and flush out all the paint. I generally punch two holes. One as close to the bottom as possible to get all the paint out and one near the top to vent it and let the paint flow out smoothly. I can also cover the top hole with my finger and control the flow. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.