Can-Con Posted May 20 Share Posted May 20 Got some this morning and tested it out on a couple parts I had laying around. No real prep, just made sure they were clean and dust free as possible and sprayed right from the can. This has only been drying for about 6 hours and is already pretty durable. I think it will be as safe to handle as any other model paint after it's dried longer. Here's an old resin bumper I cast years ago. ,, and sitting on a chrome tree for comparison. A Jo-Han 442 front bumper that had poor chrome. Just pulled it off the car, cleaned it up a bit with a toothbrush and a bit of water to get the dust off and sprayed strait from the can, as the rest of the stuff in these pics,, , , , and here's the kicker,, an old MPC Cragar sprayed on the right compared to a brand new wheel on the left,, So, while not 100% as shiny as kit plating, it's almost there. Some probably will prefer this over kit plating. Certainly better then most chrome sprays and super easy, just spray it on.I will be using this in the future for probably anything I need chromed. 10 3 Quote Link to comment Share on other sites More sharing options...
Phildaupho Posted May 21 Share Posted May 21 Looks very promising Quote Link to comment Share on other sites More sharing options...
Matt T. Posted May 21 Share Posted May 21 Thanks Steve. I think it looks better than the kit chrome in your photos! Quote Link to comment Share on other sites More sharing options...
rrb124@sbcglobal.net Posted May 21 Share Posted May 21 Looks good. Thanks for the tip. Quote Link to comment Share on other sites More sharing options...
espo Posted May 21 Share Posted May 21 The finish looks a little more realistic compared to the "kit chrome". 2 Quote Link to comment Share on other sites More sharing options...
thatz4u Posted May 21 Share Posted May 21 may be better with a black paint coating first... Quote Link to comment Share on other sites More sharing options...
Can-Con Posted May 21 Author Share Posted May 21 30 minutes ago, thatz4u said: may be better with a black paint coating first... I doubt it would make a difference Al. This stuff it pretty opaque and goes on pretty thick and evaporates down unlike Alclad and a few others that need a basecoat and go on in mist coats. But I think I'll dig out something molded in black and shoot it later to see if there's a difference. Quote Link to comment Share on other sites More sharing options...
redscampi Posted May 21 Share Posted May 21 Looks great! Too pricey for me to use regularly though... Quote Link to comment Share on other sites More sharing options...
oldr-n-drt Posted May 21 Share Posted May 21 has anyone tried decanting it an spraying it in an airbrush??oldr-n-drt Quote Link to comment Share on other sites More sharing options...
Can-Con Posted May 22 Author Share Posted May 22 3 hours ago, oldr-n-drt said: has anyone tried decanting it an spraying it in an airbrush??oldr-n-drt I'll be trying that later in the week sometime. 1 Quote Link to comment Share on other sites More sharing options...
Rodent Posted May 22 Share Posted May 22 I have had much the same great results with Spaz Stix directly over damaged kit chrome. I am curious to see how the Revell looks over black or something else that wasn't originally a chrome part. Quote Link to comment Share on other sites More sharing options...
Can-Con Posted May 22 Author Share Posted May 22 8 hours ago, Rodent said: I have had much the same great results with Spaz Stix directly over damaged kit chrome. I am curious to see how the Revell looks over black or something else that wasn't originally a chrome part. Steve, the wheel I sprayed were molded in grey and were never plated originally. They were from an MPC dodge van with the big hotrod decals on the sides. Quote Link to comment Share on other sites More sharing options...
bisc63 Posted May 22 Share Posted May 22 20 hours ago, espo said: The finish looks a little more realistic compared to the "kit chrome". Agreed, it has a nice scale-correct appearance IMHO. Pricey, but factoring in the cost (or even availability) of plating these days, it might not be so bad viewed as cost-per-model basis. It's an impressive finish for sure. 2 Quote Link to comment Share on other sites More sharing options...
1959scudetto Posted May 22 Share Posted May 22 Looks very promising, I bought myself a can a few weeks ago, will keep it for special applications. Quote Link to comment Share on other sites More sharing options...
carsntrucks4you Posted May 22 Share Posted May 22 I not a fan of Revell paint products, most of these products a junk. But this chrome spray is very good, except for its price. This gives the best chrome effect in scale modeling. Like the other chrome paints you can't clear coat it and you have to be very careful when you grab the parts. you can rub it of or it dulls when touched. 1 Quote Link to comment Share on other sites More sharing options...
Dragline Posted May 22 Share Posted May 22 I spray Alclad and Spazz Stix over light gray gloss enamel with excellent results. The issue is always handling. Keep it to a minimum and it's good. This hat and valve covers are Spazz Stix. Quote Link to comment Share on other sites More sharing options...
Can-Con Posted May 22 Author Share Posted May 22 (edited) 18 minutes ago, Dragline said: I spray Alclad and Spazz Stix over light gray gloss enamel with excellent results. The issue is always handling. Keep it to a minimum and it's good. This hat and valve covers are Spazz Stix. I've also used Alclad in the past with great results but this doesn't need a basecoat or to be airbrushed. I'm assuming this is referencing the durability questions. Edited May 22 by Can-Con Quote Link to comment Share on other sites More sharing options...
Dragline Posted May 22 Share Posted May 22 15 minutes ago, Can-Con said: I've also used Alclad in the past with great results but this doesn't need a basecoat or to be airbrushed. I'm assuming this is referencing the durability questions You would be correct. Not the shine since that is clear here. But it is delicate to say the least. Quote Link to comment Share on other sites More sharing options...
Can-Con Posted May 23 Author Share Posted May 23 41 minutes ago, Dragline said: You would be correct. Not the shine since that is clear here. But it is delicate to say the least. I've only sprayed is 2 days ago but it's already pretty durable with normal handling. The Revell parts with factory chrome I'm working with right now are scuffing up more then these are. I'm thinking it should be more durable after more drying time but only time will tell. 1 Quote Link to comment Share on other sites More sharing options...
Can-Con Posted May 23 Author Share Posted May 23 Here's a couple more pics. The old chassis was painted black and the cat was molded in black. I don't see any difference in color or shine after spraying. 3 Quote Link to comment Share on other sites More sharing options...
Dragline Posted May 23 Share Posted May 23 The evidence seems fairly clear. It makes parts chrome and in a very scale way. I think durability is only a minor issue, but it is important that it can endure some minor handling and stay as bright as when first shot. Other than the entrance fee it is a promising product. 2 Quote Link to comment Share on other sites More sharing options...
Monty Posted May 23 Share Posted May 23 23 hours ago, carsntrucks4you said: I not a fan of Revell paint products, most of these products a junk. Not to drag this thread sideways but could you elaborate on this? I've seen online reviews and pics posted here of kits painted with their enamels, and they seem to be a quality product. I'm asking because I'm thinking of using their Fiery Red on a future project, and I really don't want to have any paint issues (rare kit). Quote Link to comment Share on other sites More sharing options...
lordairgtar Posted May 23 Share Posted May 23 now to get Revell to deliver this stuff to the US hobby shops. Can't find it anywhere. And I'm not paying some schmoe a hunnert bux for the shipping. 1 Quote Link to comment Share on other sites More sharing options...
SfanGoch Posted May 23 Share Posted May 23 47 minutes ago, Monty said: Not to drag this thread sideways but could you elaborate on this? I've seen online reviews and pics posted here of kits painted with their enamels, and they seem to be a quality product. I'm asking because I'm thinking of using their Fiery Red on a future project, and I really don't want to have any paint issues (rare kit). It's more of opinion than fact. Revell paints are very good. I've been using both the Email (enamel) and Aqua Color acrylics for just about 40 years and never had a problem with either. Quote Link to comment Share on other sites More sharing options...
carsntrucks4you Posted May 23 Share Posted May 23 1 hour ago, Monty said: Not to drag this thread sideways but could you elaborate on this? I've seen online reviews and pics posted here of kits painted with their enamels, and they seem to be a quality product. I'm asking because I'm thinking of using their Fiery Red on a future project, and I really don't want to have any paint issues (rare kit). I had tried several times Revell Germany acryl paints and these are worse. The result after painting is not compareable to Tamiya or zero piants. The enamel paints are ok.. Since I had switched to Zero paints and Tamiya I'm happy. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.