Jeremy Jon

Sorry I didn't see earlier Bill, the tires are by Joseph (Fireball), excellent stuff!

Hey Ray & Bill, send me a message, I developed a ZF tranaxle proper for my Cizeta V16T build (below is 3 separate pieces, engine, bellhousing, transaxle) which should be correct for you, just adapt bellhousing from donor engine used

Super clean & nicely build, great work Mark!!

Awesome workmanship Andy, super clean & stanced builds, nicely done!!

Fantastic work Stan, your diorama especially is cool, awesome!!

Awesome workmanship Dave, I especially like the Mustang fastback with GT500 5.4L

Super clean builds Dennis, nice work, I especially like #6

Cool builds Curt, and super clean, nicely done!!

Nice work Emmanuel, well done!!

Heck of large project, great work Bill, and inspiring too, bravo!!

Looks much better Ray, neat project, cool !

Lots of great detailing, nicely done, looking forward to more!

Bill's post is 100% correct, the H&M Coyote kit base is from the MkIV set, and the bodywork is not accurate (horrible) in almost every detail The H&M show car(s) were in fact replicas (Manta), the bodywork molds taken directly off of a (Trojan built) McLaren M6GT I have to update my thread, but my parallel build is to result in a full detail McLaren M6GT and Coyote, because I have never found a 24th scale M6GT in all my searching, and want one which is more than just a curb-side kit, so will have individual each accurate chassis, sharing only the basic bodywork structures, waiting for some digital 3D printed parts for them right now, then I'll add a bunch more updates

Modified tires now cast into hard resin, as masters for softer rubber recasting next

Great build & subject Geoff, looking great!

Thanks Kerry, no you can't stop man! I fight with finishing work (paint & decals especially) so I do scratch building ...besides, we gotta see your McFerrariLaren finished!

Thanks Tim Found some correct Goodyear donor tires, but only these 2, also needed modification to make correct widths The AMX3 used 205 front & 225 rear section tires Now will make hard resin copes for master set, and then recast into a softer rubber

Thanks Bruce & William

Very nice result on the printing, it certainly is an amazing new tool ...like with most things, the catch is the design process & time it takes, I'm always amazed by people's results, but fully aware of the hours they put into the initial design work to create a STL file

Thanks guys, Miles, Bob, Ismael, Bill, Fabrizio, Brian, Ken & Tim Brizio, last PM was Nov 18, my reply to you about items I sent you & transporter, PM me again if you sent since then I've always liked this car too, was a unique '90's big supercar, and one of the first 200mph supercar crop to be sure I started on some accessory items, like manifolds, starter, etc. and then some cursory molds, pretty happy with how the first resin bits of the drivetrain came out Found a correct O.Z. racing 3-piece wheel, so now will modify it to make correct front & rear staggered set for model, and use the Tamiya F40 P-zero tires, which are correct for the car

Neat project idea Ismael, looks great, looking forward to seeing more!

Looking good, always liked the gen3 RX7s ..those wheels look nice with too!

Unique build project Rob, shaping up nicely! True, mother mopar never did have (to my knowledge) a "ute" based on any of it's RWD car platforms, only the Rampage (as mentioned) which was based on the FWD K-car platform. Looking forward to seeing more!

Nice work Tom, looking great! The engine stands out due to being so clean in comparison to the engine bay, are you going to wash that also for effect? I like using brown in wash mix also, for 'grime' effect. Great work, looking forward t o seeing more!

Nice workmanship Mark, every one is awesome! Love that slamm'd Z28