SSNJim

I can relate. The Slammer wasn't that bad (no texture). The 57 Chevy and Chezoom that I gave the same treatment were quite the projects. I didn't do both at the same time; I waited until I forgot the effort it took to do the first before starting the second. Actually, I just looked at your last build post since it was after the one I replied to. Your body and the Slammer are quite different. The Slammer body disposes with such frivolities as fuel doors, the fins are a bit higher, and it has custom bumpers and nothing between the spears. You did a fine job removing the trim. Looking forward to this build. I always enjoy your builds.

I thought the 58 Fury and Belvedere were pretty much the same cars. the difference being the paint and trim level. Furys only came in one color with the side spear painted gold with bright chrome trim. I could be wrong though, since I'm no Mopar expert. On the Street Fury slammer I built, I took only the top part of the side trim off, so there's one continuous molding (the stock lower) from the headlights to the rear bumper.

I guess it depends on who you ask. My ex-wife had an uncle who was a carpenter years and years ago. He said one foreman told him to use a hammer to drive wood screws in - the slots in the top of the screw were for removing it.

The only hobby shops I know of are Hobby Works (there are two stores - one in Rockville, MD and the other in Laurel, MD). There is Star Hobby in Annapolis, MD, and a Hobby Town USA in Frederick, MD. You can get the addresses and hours by googling the names. There are a few Hobby Lobby and Michael's stores (both primarily craft stores). I'm not sure what there is in VA anymore - all the ones I knew of are gone but I don't get there often nowadays. A wprd of warning - when you go to the hobby stores, watch the time you go. Afternoon rush hour can be horrible heading to any of them from near DC. Star Hobby is very near the Chesapeake Bay Bridge, and the last couple of miles on weekends can take a half hour or more. Not sure of what there is club/show related, but most stuff is done on weekends. Hope others jump in with more hobby shops.

Very similar. Note that the logo on the front wheel is upright. It was wild to see it not spinning like a regular car.

The other day I saw a newer Rolls-Royce going down the road. It had "spinner hubcaps" from the factory. Most of the wheel cover was rotating with the tire, but the center (where you would normally see the Ford, Chevy, Honda, or whatever logo) kept the RR logo upright the whole time so you could definitely tell what was being driven. They did rock a bit, but they never moved more than 10-15 degrees. The section not rotating was probably 4-6" in diameter.

Similar story with our 2018 Escape. The dealer wouldn't rotate the tires anymore until we had them changed (at 40,000 miles). We went round and round with them, and ended up buying a set at a local auto parts store. They were happy to change them out for us at the next oil change/tire rotation. I never understood how a metal lug nut in the Mid-Atlantic climate could "swell". Obviously there is something I don't quite understand about modern lug nut technology since I've never heard of lug nut swell. I've never taken a wheel off the Escape. No issues with our 2007 Mustang.

It worked very well. I never suspected it was a compact digital camera. I was thinking GoPro or something similar.

Very nice work and video - quite realistic. I don't know what camera you used to video it, but I really liked the effect. I felt like I was walking around the diorama. Well done!

My 07 Mustang developed that dashboard leak in a heavy rainstorm one day. The cabin air filter receptacle drain got clogged up with pine needles and leaves, and overflowed through the filter into the ventilation fan blades then into the interior. What a mess. I know what you went through. It is pretty scary - I was worried it was a coolant leak at first and the fan made noise until it dried out.

Nice work. I've got a Deserter conversion in progress. The cab and frame are extended, and everything is roughed in. I'm hoping it comes out anywhere near as good as yours. If you're in the planning stages, check out the GM Vehicle Information Kits at Vehicle Information Kits | GM Heritage Archive | General Motors . Great place for dimensions and other specs.

I was browsing Reddit, and I found this fascinating video. I must have watched it a dozen times. Uh, so far. It's nothing more than one minute of cars with pop-up/hidden headlights being activated. There is everything from Cords to Ferraris to Opel GTs. I've often wondered how the headlights on a Buick Riviera or Chevrolet Camaro worked; it was answered here. Unfortunately I wasn't able to find a URL direct to this video , so here is the link to Reddit. I did check and found no profanity or offensive material; I would consider it safe for work. https://www.reddit.com/r/oddlysatisfying/comments/12kd3ny/popup_headlights/ Searching YouTube for "dtrockstar1 headlights" will provide other videos by the same creator with the same subject, some much longer than a minute. Enjoy!

But then again, I had a 1965 Chevy Bel Air wagon, and a friend of mine had a 1965 Chevy Impala 2-door. My door keys would start his car, and his would start mine. The ignition keys would work on the doors. Automotive security has been a problem for a long time, and I wouldn't expect it to get much better - only different.

They make pretty nice wreaths, too.

Thanks. I'll give it a try.

The limber holes look really good. How did you do it? I've got a couple of Type VIIs and XIXs, along with a few Gatos in 1/350. They just don't look right without the work on the limber holes. Thanks!

I remember that being a thing in Louisville, KY in the early to mid 70s. The rock station there would play a full album (or at least one side) in the wee hours of the morning - no commercials. I assume it was to avoid paying DJs. I would imagine there was a technician or someone to flip sides or put the needle back in the groove. This was also the era of TV stations signing off at 11pm or 12am.

Testors also did a yellow version of the Boyd's Hauler with a different name and the same wheels. It was a simple curbside kit with solid black windows and no interior.

Ha! Found the picture. It wasn't the Atlantic, but it was Lindberg in November 2018.

One day at Ollie's quite a while back I found a kit (I think it was a Lindberg Chrysler Atlantic) that had an inscription on the box in Sharpie. It was an inspirational note. I think it came from one of the models for veterans-type thing. Very odd. I was wondering the same thing about Ollie's and their wrappings.

Maybe it has something to do with removale?

I was at my LHS a few minutes ago, and they had the Revell snap-kit New Beetle for $41.99. That happened to be the same price as the Revell AMG GT glue kit (93 pieces). I was thinking of picking up the VW, but not at that price.

This is the one I use. It seems a little more comprehensive than Old Car Brochures: Brochures (lov2xlr8.no) That Comet is a very nice find.

This is the one I use. It seems a little more comprehensive than Old Car Brochures: Brochures (lov2xlr8.no)