NOBLNG

Get yourself a cheap food dehydrator (one with adjustable temp control) to use as a drying booth. It is also good for keeping your paint cans warm in colder weather. There is a sticky in the Q&A section on them.

Very nice. Good job on the woodgrain!

On a related note, I just tried another test with 1/16” round. The Tamiya QS cement made the bend snap. The Plastruct did not. I got the Plastruct on my last trip to the hobby shop cause it was on sale. I can see why because it sure doesn’t weld styrene together the way the Tamiya does!?

Yes, thanks Guys! Things seem to be OK now.?

I just tried an experiment. I heated the two plates clamped in the vise slightly. Then put the .060” half round in and bent it around the .030” spacer. It stayed very nearly flat.

That is when it usually snaps for me. What size half round and what radius are you using? Any pics of what you are trying to do?

The OP could possibly bend round stock of the same diameter, sand the bottom half off and use the curved section? Not ideal as it makes for joints in the trim, but a possibility?

I see it in this thread now. When I first posted in this thread on Wednesday, it was full screen. None of the threads in “under glass” display it and only some threads in other sections??? Edit: Steven’s ‘65 Plymouth thread does it in the under glass section.

Very cool project! I like!?

I have also heard that coating the strip with solvent and letting it “soak” for a while to soften the styrene before bending may work. I still think it may snap, but you could try a test?

I agree, the roof change looks great on this car.?

Solvent glues will only work for styrene to styrene joints I believe. To glue anything to resin you would need CA or epoxy. I’ve never tried a PVA (white glue) or canopy cement, so I don’t know about those? Best to shape the strips to the contour needed beforehand so the glue is not tasked with holding the shape, especially if it’s a sharp curve.

Where’s the orange peel when you want it eh?

I am retired also, so I work on them everyday unless the wife comes up with a plan for the day. I usually have 2 or 3 going so I am not tempted to rush the paint and glue drying...but this scratch building is obsessive.

I have had curved styrene strips break the instant that I applied a solvent cement to them. I wouldn’t think CA would do that If the strip is already preformed to the finished shape. I have also used 5 minute epoxy which allows you time to play with the positioning, but it does squish out a bit and requires cleanup.

Thanks Steve, Anton, Tom! ? I didn’t like the styrene plank and screws holding the hinge onto the toolbox, so I got rid of them. I epoxied the hinge on and camouflaged the holes. The next items I have to fab are some bumpers and an exhaust system.

I don’t see any arrow pointing right. There is an ad at the top of the page. When I close it, an arrow appears on the left that brings the ad back when clicked.

I think I read on here a while back that someone either glued a fabric softener sheet on the floorpan, or dabbed the wet paint with it to mimic the raw fiberglass texture.

Since the update, some threads have 1/3 of the screen on the right taken up by “thread statistics” and the actual post section is only 2/3 of the screen on my i-pad. This particular thread is full screen.? Has anyone else’s display gotten smaller and is there any way to get back to a full screen?

So...since this thread is about lousy ‘57s, how does this old kit compare accuracy wise? I searched this site via google and could not find pics of a built one. I gathered that the doors don’t fit proper or are finicky, and the plastic is brittle. One member said he built a few and had no issues with it.

Well it’s been slow going on this project. I’ve gotten lots of fiddly little things done though. Steering linkage is fabbed now and hooked up. I’ve re-made the rear shocks and roughed in the mounts for them and mounted a fuel tank. I mounted the tailgate and fuel filler tube and also managed to get a coat of primer on it so that I can see what needs a little more body work...mostly the grill area I think. My checker plate from Slaters arrived, so I got to work making my toolbox and box cover. I’ve been dabbling a bit with brass lately and made some hood hinges for it and these little gas shocks that hold the box lid up.?

This is Tamiya TS-7 “Racing White” in the interior. I’ve never seen a paint called parchment.

Nice job on that chop.?

Super nice job there Helmut. I never would have thought that was done with rattle cans.?

Type this into google and maybe the thread will be there? ”site:modelcarsmag.com tube chassis” You can substitute “tube chassis” for other cues. Good luck